參數資料
型號： UCC35701N
英文描述： Precision 500 mA regulators
中文描述： 電壓模式開關電源控制器
文件頁數： 4/10頁
文件大?。?/td> 371K
代理商： UCC35701N
4
UCC1580-1,-2,-3,-4
UCC2580-1,-2,-3,-4
UCC3580-1,-2,-3,-4
ELECTRICAL CHARACTERISTICS
Unless otherwise stated, all specifications are over the full temperature range, VDD
= 12V, R1 = 18.2k, R2 = 4.41k, C
T
= 100pF, R3 = 100k, C
OUT1
= 0, C
OUT2
= 0. T
A
= 0°C to 70°C for the UCC3580,
40°C to 85°C
for the UCC2580,
55°C to 125°C for the UCC1580, T
A
= T
J
.
PARAMETER
TEST CONDITIONS
Output Drivers Section (cont.)
OUT2 Rise Time
C
OUT2
= 300pF, R
S
= 10
Delay 1 OUT2 to OUT1
R3 = 100k, C
OUT1
= C
OUT2
= 15pF
T
A
= T
J
= 25°C
Delay 2 OUT1 to OUT2
R3 = 100k, C
OUT1
= C
OUT2
= 15pF
T
A
= T
J
= 25°C
Reference Section
REF
I
REF
= 0
Load Regulation
I
REF
= 0mA to 1mA
Line Regulation
VDD = 10V to 14V
MIN
TYP
MAX
UNITS
20
120
120
170
170
40
160
140
250
200
ns
ns
ns
ns
ns
90
100
110
140
4.875
5
1
1
5.125
20
20
V
mV
mV
CLK: Oscillator clock output pin from a low impedance
CMOS driver. CLK is high during guaranteed off time.
CLK can be used to synchronized up to five other
UCC3580 PWMs.
DELAY:
A resistor from DELAY to GND programs the
nonoverlap delay between OUT1 and OUT2. The delay
times, Delay1 and Delay2, are shown in Figure 1 and are
as follows:
Delay
pF
R
1 11
3
.
Delay2 is designed to be larger than Delay1 by a ratio
shown in Figure 2.
EAIN:
noninverting input of the error amplifier is internally set to
2.5V. EAIN is used for feedback and loop compensation.
Inverting
input
to
the
error
amplifier.
The
EAOUT:
Output of the error amplifier and input to the
PWM
comparator.
Loop
connect from EAOUT to EAIN.
compensation
components
GND:
Signal Ground.
LINE:
Hysteretic comparator input. Thresholds are 5.0V
and 4.5V. Used to sense input line voltage and turn off
OUT1 when the line is low.
OSC1 & OSC2:
Oscillator programming pins. A resistor
connects each pin to a timing capacitor. The resistor
connected to OSC1 sets maximum on time. The resistor
connected to OSC2 controls guaranteed off time. The
combined total sets frequency with the timing capacitor.
Frequency and maximum duty cycle are approximately
given by:
1
R1 1.25 R2
(
)
Frequency
CT
=
Maximum Duty Cycle
R1
R1 1.25 R2
=
Maximum Duty Cycle for OUT1 will be slightly less due to
Delay1 which is programmed by R3.
OUT1:
Gate drive output for the main switch capable of
sourcing up to 0.5A and sinking 1A.
OUT2:
Gate drive output for the auxiliary switch with
±
0.3A drive current capability.
PGND:
Ground connection for the gate drivers. Connect
PGND to GND at a single point so that no high frequency
components of the output switching currents are in the
ground plane on the circuit board.
RAMP:
A resistor (R4) from RAMP to the input voltage
and a capacitor (CR) from RAMP to GND programs the
feedforward ramp signal. RAMP is discharged to GND
when CLK is high and allowed to charge when CLK is
low. RAMP is the line feedforward sawtooth signal for the
PWM comparator. Assuming the input voltage is much
greater than 3.3V, the ramp is very linear. A flux
comparator compares the ramp signal to 3.3V to limit the
maximum allowable volt-second product:
Volt-Second Product Clamp = 3.3 R4 CR.
REF:
Precision 5.0V reference pin. REF can supply up to
5mA to external circuits. REF is off until VDD exceeds 9V
(–1 and –3 versions) or activates the 15V clamp (–2 and
–4 versions) and turns off again when VDD droops below
8.5V. Bypass REF to GND with a 1
μ
F capacitor.
SHTDWN:
Comparator input to stop the chip. The
threshold is 0.5V. When the chip is stopped, OUT1 is low
and OUT2 continues to oscillate with guaranteed off time
equal to two non-overlap delay times.
PIN DESCRIPTIONS
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料
PDF描述
UCC35701PW Voltage-Mode SMPS Controller
UCC35702D Voltage-Mode SMPS Controller
UCC35702N 5.0 AMP POSITIVE VOLTAGE REGULATOR
UCC35702PW 5.0 AMP POSITIVE VOLTAGE REGULATOR
UCC3580Q-2 5.0 AMP POSITIVE VOLTAGE REGULATOR
相關代理商/技術參數
參數描述
UCC35701N 制造商:Texas Instruments 功能描述:IC PWM CONTROLLER 35701 DIP14
UCC35701NG4 功能描述:電壓模式 PWM 控制器 Adv Voltage Mode RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
UCC35701PW 功能描述:電壓模式 PWM 控制器 Adv Voltage Mode RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
UCC35701PWG4 功能描述:電壓模式 PWM 控制器 Adv Voltage Mode RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
UCC35701PWTR 功能描述:電壓模式 PWM 控制器 Adv Voltage Mode RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*