![](http://datasheet.mmic.net.cn/200000/UCC2813-2QDRQ1_datasheet_15111165/UCC2813-2QDRQ1_3.png)
UCC28130/1/2/3/4/5Q1
LOW POWER BICMOS CURRENT MODE PWM
SGLS245B MAY 2004 = REVISED APRIL 2006
3
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
Ordering Information
UCC 20
Q
PACKAGE
D = Plastic SOIC, PW = Plastic TSSOP
PRODUCT OPTION
0 through 5
AUTOMOTIVE TEMPERATURE RANGE INDICATOR
D
TAPE and REEL INDICATOR
R
813-
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
VCC voltage w
12 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VCC current w
30 mA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output current, IO
±1 A
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output energy, (Capacitive Load)
20
J
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Inputs (FB, CS)
0.3 V to 6.3 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Dissipation at TA < +25_C (D package)
0.65 W
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg
65
_C to 150_C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds
300
_C
. . . . . . . . . . . . . . . . . . . . . . .
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Unless otherwise indicated, voltages are reference to ground and currents are positive into and negative out of the specified terminals.
w In normal operation VCC is powered through a current limiting resistor. Absolute maximum of 12 V applies when VCC is driven from a low
impedance source such that ICC does not exceed 30 mA (which includes gate drive current requirement).
electrical characteristics TA = 40_C to 125_C, VCC = 10 V (see Note 1), RT = 100 k from REF to
RC, CT = 330 pF from RC to GND, 0.1-F capacitor from VCC to GND, 0.1-F capacitor from VREF to
GND and TA = TJ (unless otherwise stated)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Reference Section
Output voltage
TJ = 25_C, I = 0.2 mA
UCC2813-0/1/2/4
4.925
5
5.075
V
Output voltage
TJ = 25_C, I = 0.2 mA
UCC2813-3/5
3.94
4
4.06
V
Load regulation voltage
I = 0.2 mA to 5 mA
10
30
mV
Total variation voltage
See Note 5
UCC2813-0/1/2/4
4.84
5
5.1
V
Total variation voltage
See Note 5
UCC2813-3/5
3.84
4
4.08
V
Output noise voltage
f = 10 Hz to 10 kHz,
See Note 7
TJ = 25_C
70
V
Long term stability
1000 hours,
See Note 7
TA = 125_C
5
mV
Output short-circuit current
5
35
mA