- 您現在的位置：買賣IC網 > PDF目錄381159 > UCC1946PWTR Very low drop voltage regulators with inhibit PDF資料下載
參數資料
| 型號： | UCC1946PWTR |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Very low drop voltage regulators with inhibit |
| 中文描述： | 工業控制IC |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 156K |
| 代理商： | UCC1946PWTR |
5
UCC1946
UCC2946
UCC3946
Figure 5. Reset circuit timings.
t1:
V
DD
> 1V, RES is guaranteed low.
t2:
V
DD
> programmed threshold, RES remains low for
T
RP
.
t3:
T
RP
expires, RES pulls high.
t4:
Voltage glitch occurs, but is filtered at the RTH pin,
RES remains high.
t5:
Voltage glitch occurs whose magnitude and dura-
tion is greater than the RTH filter, RES is asserted for
T
RP
.
t6:
V
DD
dips below threshold (minus hysteresis), RES
is asserted.
UDG-97067
In order to provide design flexibility, the reset and watch-
dog circuits in the UCC3946 have separate outputs.
Each output will independently drive high or low, depend-
ing on circuit conditions explained previously.
In some applications, it may be desirable for either the
RES or WDO to reset the microprocessor. This can be
done by connecting WDO to RES. If the pins try to drive
to different output levels, the low output level will domi-
nate. Additional current will flow from VDD to GND during
these states. If the application cannot support additional
current (during fault conditions), RES and WDO can be
connected to the inputs of an OR gate whose output is
connected to the microprocessor’s reset pin.
Layout Considerations
A 0.1
μ
F capacitor connected from V
DD
to GND is recom-
mended to decouple the UCC3946 from switching tran-
sients on the V
DD
supply rail.
Since RP and WP are precision current sources, capaci-
tors C
RP
and C
WP
should be connected to these pins
with minimal trace length to reduce board capacitance.
Care should be taken to route any traces with high volt-
age potential or high speed digital signals away from
these capacitors.
Resistors R1 and R2 generally have a high ohmic value,
traces associated with these parts should be kept short
in order to prevent any transient producing signals from
coupling into the high impedance RTH pin.
APPLICATION INFORMATION (cont.)
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| UCC2918L | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| UCC2918Q | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| UCC2919DTR | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| UCC2919J | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| UCC2919PWTR | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCC1972 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:BiCMOS Cold Cathode Fluorescent Lamp Driver Controller |
| UCC1972_13 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:BiCMOS Cold Cathode Fluorescent Lamp Driver Controller |
| UCC1972J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ballast/Backlight Controller/Driver |
| UCC1973 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:BiCMOS Cold Cathode Fluorescent Lamp Driver Controller |
| UCC20225NPLT | 功能描述:DGTL ISO 2.5KV GATE DRVR 13VLGA 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:在售 技術:容性耦合 通道數:2 電壓 - 隔離:2500Vrms 共模瞬態抗擾度（最小值）:100V/ns 傳播延遲 tpLH / tpHL（最大值）:30ns，30ns 脈寬失真（最大）:6ns 上升/下降時間（典型值）:6ns，7ns 電流 - 輸出高，低:4A，6A 電流 - 峰值輸出:- 電壓 - 正向（Vf）（典型值）:- 電壓 - 電源:3 V ~ 18 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:13-VLGA 供應商器件封裝:13-VLGA（5x5） 認可:CQC，CSA，UR，VDE 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。