- 您現在的位置：買賣IC網 > PDF目錄382720 > UCC1926DS Very low drop voltage regulators with inhibit PDF資料下載
參數資料
| 型號： | UCC1926DS |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Very low drop voltage regulators with inhibit |
| 中文描述： | 一般應用檢測放大器 |
| 文件頁數： | 1/9頁 |
| 文件大小： | 158K |
| 代理商： | UCC1926DS |
UCC1913
UCC2913
UCC3913
DESCRIPTION
The UCC1913 family of negative voltage circuit breakers provides com-
plete power management, hot swap, and fault handling capability. The IC is
referenced to the negative input voltage and is driven through an external
resistor connected to ground, which is essentially a current drive as op-
posed to the traditional voltage drive. The on-board 10V shunt regulator
protects the IC from excess voltage and serves as a reference for program-
ming the maximum allowable output sourcing current during a fault. All
control and housekeeping functions are integrated, and externally program-
mable. These include the fault current level, maximum output sourcing cur-
rent, maximum fault time, soft start time, and average power limiting. In the
event of a constant fault, the internal timer will limit the on-time from less
than 0.1% to a maximum of 3%. The duty cycle modulates depending on
the current into the PL pin, which is a function of the voltage across the
FET, and will limit average power dissipation in the FET. The fault level is
fixed at 50mV across the current sense amplifier to minimize total dropout.
The fault current level is set with an external current sense resistor. The
maximum allowable sourcing current is programmed with a voltage divider
from VDD to generate a fixed voltage on the IMAX pin. The current level,
when the output appears as a current source, is equal to V
IMAX/
R
SENSE
. If
desired, a controlled current startup can be programmed with a capacitor
on the IMAX pin.
When the output current is below the fault level, the output device is
switched on. When the output current exceeds the fault level, but is less
than the maximum sourcing level programmed by the IMAX pin, the output
remains switched on, and the fault timer starts charging CT. Once CT
charges to 2.5V, the output device is turned off and performs a retry some
time later. When the output current reaches the maximum sourcing current
level, the output appears as a current source, limiting the output current to
the set value defined by IMAX.
Other features of the UCC1913 family include undervoltage lockout, and
8-pin small outline (SOIC) and Dual-In-Line (DIL) packages.
Negative Voltage Hot Swap Power Manager
FEATURES
Precision Fault Threshold
Programmable Average Power
Limiting
Programmable Linear Current Control
Programmable
Overcurrent Limit
Programmable Fault Time
Fault Output Indication
Shutdown Control
Undervoltage Lockout
8-Pin SOIC
1/99
1
2
LINEAR
CURRENT
AMPLIFIER
PL
7
OUT
IMAX
+
V
DD
50
8
V
DD
6
SENSE
5
VSS
4
CT
ON-TIME
CONTROL
3
VDD
UVLO
5.0V
REF
LOGIC
SUPPLY
9.5V SHUNT REGULATOR
+
20
μ
A
1=
UNDERVOLTAGE
SOURCE
ONLY
SD/FLT
V
DD
0.2V
OVERCURRENT
COMPARATOR
DISABLE
5.0V
OVERLOAD COMPARATOR
50mV
BLOCK DIAGRAM
UDG-99001
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| UCC3913J | Analog IC |
| UCH81 | TRIODE HEPTODE |
| UCS51 | Dual step-down main supply controller with auxilary voltages for notebook system power |
| UDA1309H | Low-power stereo bitstream ADC/DAC(低功耗立體聲位流ADC/DAC) |
| UDA1320ATS | Low-Cost Stereo Filter DAC(低價格立體聲濾波數模轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCC1926SPWIP | 制造商:Texas Instruments 功能描述: |
| UCC19411 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low Power Synchronous Boost Converter |
| UCC19412 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low Power Synchronous Boost Converter |
| UCC19413 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low Power Synchronous Boost Converter |
| UCC1946 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Microprocessor Supervisor with Watchdog Timer |
發布緊急采購，3分鐘左右您將得到回復。