- 您現在的位置：買賣IC網 > PDF目錄381149 > UC3845 (ON SEMICONDUCTOR) High Performance Current Mode Controllers(高性能電流模式控制器) PDF資料下載
參數資料
| 型號： | UC3845 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | High Performance Current Mode Controllers(高性能電流模式控制器) |
| 中文描述： | 高性能電流模式控制器（高性能電流模式控制器） |
| 文件頁數： | 9/16頁 |
| 文件大小： | 354K |
| 代理商： | UC3845 |
UC3844, UC3845, UC2844, UC2845
http://onsemi.com
9
Undervoltage Lockout
Two undervoltage lockout comparators have been
incorporated to guarantee that the IC is fully functional
before the output stage is enabled. The positive power
supply terminal (V
CC
and the reference output (V
ref
) are
each monitored by separate comparators. Each has builtin
hysteresis to prevent erratic output behavior as their
respective thresholds are crossed. The V
CC
comparator
upper and lower thresholds are 16 V/10 V for the UCX844,
and 8.4 V/7.6 V for the UCX845. The V
ref
comparator upper
and lower thresholds are 3.6 V/3/4 V. The large hysteresis
and low startup current of the UCX844 makes it ideally
suited in offline converter applications where efficient
bootstrap startup techniques later required (Figure 30). The
UCX845 is intended for lower voltage DCtoDC converter
applications. A 36 V zener is connected as a shunt regulator
from V
CC
to ground. Its purpose is to protect the IC from
excessive voltage that can occur during system startup. The
minimum operating voltage for the UCX844 is 11 V and
8.2 V for the UCX845.
Output
These devices contain a single totem pole output stage that
was specifically designed for direct drive of power
MOSFETs. It is capable of up to
±
1.0 A peak drive current
and has a typical rise and fall time of 50 ns with a 1.0 nF load.
Additional internal circuitry has been added to keep the
Output in a sinking mode whenever and undervoltage
lockout is active. This characteristic eliminates the need for
an external pulldown resistor.
The SOIC14 surface mount package provides separate
pins for V
C
(output supply) and Power Ground. Proper
implementation will significantly reduce the level of
switching transient noise imposed on the control circuitry.
This becomes particularly useful when reducing the I
pk(max)
clamp level. The separate V
C
supply input allows the
designer added flexibility in tailoring the drive voltage
independent of V
CC.
A zener clamp is typically connected
to this input when driving power MOSFETs in systems
where V
CC
is greater the 20 V. Figure 23 shows proper
power and control ground connections in a current sensing
power MOSFET application.
Reference
The 5.0 V bandgap reference is trimmed to
±
1.0%
tolerance at T
J
= 25
°
C on the UC284X, and
±
2.0% on the
UC384X. Its primary purpose is to supply charging current
to the oscillator timing capacitor. The reference has short
circuit protection and is capable of providing in excess of
20 mA for powering additional control system circuitry.
Design Considerations
Do not attempt to construct the converter on
wirewrap or plugin prototype boards.
High frequency
circuit layout techniques are imperative to prevent
pulsewidth jitter. This is usually caused by excessive noise
pickup imposed on the Current Sense or Voltage Feedback
inputs. Noise immunity can be improved by lowering circuit
impedances at these points. The printed circuit layout should
contain a ground plane with lowcurrent signal and
highcurrent switch and output grounds returning on
separate paths back to the input filter capacitor. Ceramic
bypass capacitors (0.1 F) connected directly to V
CC
, V
C
,
and V
ref
may be required depending upon circuit layout.
This provides a low impedance path for filtering the high
frequency noise. All high current loops should be kept as
short as possible using heavy copper runs to minimize
radiated EMI. The Error Amp compensation circuitry and
the converter output voltage divider should be located close
to the IC and as far as possible from the power switch and
other noise generating components.
External
Sync
Input
Figure 18. External Clock Synchronization
Figure 19. External Duty Cycle Clamp and
MultiUnit Synchronization
The diode clamp is required if the Sync amplitude is large enough to
cause the bottom side of CT to go more than 300 mV below ground.
47
5(9)
R
R
Bias
OSC
V
ref
R
T
8(14)
4(7)
2(3)
1(1)
0.01
C
T
2R
R
EA
+
+
5(9)
R
R
Bias
OSC
8(14)
4(7)
2(3)
1(1)
2R
R
EA
+
+
7
5.0k
+
3
8
6
5
2
1
C
R
S
MC1455
R
A
+
4
Q
5.0k
5
R
B
To
Additional
UCX84XA’s
f =
1.44
(R
A
+ 2R
B
)C
D
max
=
R
B
R
A
+ 2R
B
相關PDF資料 |
PDF描述 |
|---|---|
| UC2845AAY | CURRENT MODE PWM CONTROLLER |
| UC284XA | CURRENT MODE PWM CONTROLLER |
| UC2845AL | |
| UC1842AL | Automotive 8-bit MCU, with up to 32 Kbytes Flash, EEPROM, 10-bit ADC, timers, LIN, SPI, I2C, 3 V to 5.5 V |
| UC1849DW | Digitally controlled audio processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UC3845A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Current Mode PWM Controller |
| UC3845A-BW | 制造商:FCI 制造商全稱:First Components International 功能描述:Current Mode PWM Controller Low Start-Up and Operating Current |
| UC3845AD | 功能描述:電流型 PWM 控制器 Current Mode RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| UC3845AD1 | 功能描述:電流型 PWM 控制器 RO 511-UC3845BD 9/04 RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| UC3845AD1013TR | 制造商:STMicroelectronics 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。