- 您現在的位置：買賣IC網 > PDF目錄381156 > UC27131DTR HIGH SIDE DRIVER PDF資料下載
參數資料
| 型號： | UC27131DTR |
| 英文描述： | HIGH SIDE DRIVER |
| 中文描述： | 單外設驅動 |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 547K |
| 代理商： | UC27131DTR |
Overload Protection:
The circuit is equipped with a
thermal shutdown function, which will limit the junction
temperature by reducing the output current. It should be
noted however, that a short circuit of the output is not
permitted.
Operation:
When the voltage is applied across the motor
winding the current rises linearly and appears across the
external sense resistor as an analog voltage. This volt-
age is fed through a low pass filter R
C
, C
C
to the voltage
comparator (pin 10). At the moment the voltage rises be-
yond the comparator threshold voltage the monostable is
triggered and its output turns off the sink transistors. The
current then circulates through the source transistor and
the appropriate Schottky diode. After the one shot has
timed out, the sink transistsor is turned on again and the
procedure repeated until a current reverse command is
given. By reversing the logic level of the phase input (pin
8), both active transistors are being turned off and the
opposite pair turned on. When this happens the current
must first decay to zero before it can reverse. The cur-
rent path then provided is through the two diodes and the
power-supply. Refer to Figure 7. It should be noted at
this time that the slope of the current decay is steeper,
and this is due to the higher voltage build up across the
winding. For better speed performance of the stepping
motor at half step mode, the phase logic level should be
changed at the same time the current inhibit is applied. A
typical current wave form is shown in Figure 8.
APPLICATIONS
A typical chopper drive for a two phase bipolar perma-
nent magnet or hybrid stepping motor is shown in Figure
9. The input can be controlled by a microprocessor, TTL,
LS or CMOS logic.
The timing diagram in Figure 10 shows the required sig-
nal input for a two phase, full step, stepping sequence.
Figure 11 shows a one phase, full step, stepping se-
quence, commonly referred to as wave drive. Figure 12
shows the required input signal for a one phase-two
phase stepping sequence called half-stepping.
The circuit of Figure 13 provides the signal shown in Fig-
ure 10, and in conjunction with the circuit shown in Fig-
ure 9, will implement a pulse-to-step two phase, full step,
bidirectional motor drive.
The schematic of Figure 14 shows a pulse to half step
circuit generating the signal shown in Figure 12. Care
has been taken to change the phase signal the same
time the current inhibit is applied. This will allow the cur-
rent to decay faster and therefore enhance the motor
performance at higher step rates.
Using the UC3717 to drive the L298 provides a uniquely
packaged state-of-the-art high power stepper motor con-
trol and drive. See Figure 15.
Figure 8
FUNCTIONAL DESCRIPTION (cont.)
Figure 9
UC1717
UC2717
UC3717
5
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| UC27131N | HIGH SIDE DRIVER |
| UC27132D | HIGH SIDE DRIVER |
| UC27132DTR | HIGH SIDE DRIVER |
| UC27132N | HIGH SIDE DRIVER |
| UC27133D | HIGH SIDE DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UC27131N | 功能描述:電源開關 IC - 配電 Low Side Smart Power Switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| UC27131NG4 | 功能描述:電源開關 IC - 配電 Low Side Smart Power Switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| UC27132 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Smart Power Switch |
| UC27132D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single Peripheral Driver |
| UC27132DTR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single Peripheral Driver |
發布緊急采購，3分鐘左右您將得到回復。