- 您現在的位置：買賣IC網 > PDF目錄380956 > UC2526DWTR LOW POWER VOLTAGE REGULATOR PDF資料下載
參數資料
| 型號： | UC2526DWTR |
| 英文描述： | LOW POWER VOLTAGE REGULATOR |
| 中文描述： | 電壓模式開關電源控制器 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 618K |
| 代理商： | UC2526DWTR |
TTL, open-drain CMOS, and open-collector voltage com-
parators; fan-in is equivalent to 1 low-power Schottky
gate.
Each port is normally HIGH; the pin is pulled LOW
to activate the particular function. Driving SYNC
SHUTDOWN
LOW immediately inhibits all PWM output
pulses. Holding RESET
LOW discharges the soft-start
capacitor. The logic threshold is +1.1V at +25°C. Noise
immunity can be gained at the expense of fan-out with an
external 2k pull-up resistor to +5V.
LOW in-
____________
Oscillator
The oscillator is programmed for frequency and dead time
with three components: R
T
, C
T
and R
D
. Two waveforms
are generated: a sawtooth waveform at pin 10 for pulse
width modulation, and a logic clock at pin 12. The follow-
ing procedure is recommended for choosing timing val-
ues:
1. With R
D
= 0 (pin 11 shorted to ground) select values
for R
T
and C
T
from Figure 7 to give the desired oscillator
period. Remember that the frequency at each driver out-
put is half the oscillator frequency, and the frequency at
the +V
C
terminal is the same as the oscillator frequency.
2. If more dead time is required, select a large value of
R
D
. At 40kHz dead time increases by 400ns/
.
3. Increasing the dead time will cause the oscillator fre-
quency to decrease slightly. Go back and decrease the
value of R
T
slightly to bring the frequency back to the
nominal design value.
The UC1526 can be synchronized to an external logic
clock by programming the oscillator to free-run at a fre-
quency 10% slower than the sync frequency. A periodic
LOW logic pulse approximately 0.5
μ
s wide at the SYNC
pin will then lock the oscillator to the external frequency.
Multiple devices can be synchronized together by pro-
gramming one master unit for the desired frequency and
then sharing its sawtooth and clock waveforms with the
slave units. All C
T
terminals are connected to the C
T
pin
of the master, and all SYNC
nected to the SYNC
pin of the master. Slave R
T
termi-
nals are left open or connected to V
REF
. Slave R
D
terminals may be either left open or grounded.
terminals are likewise con-
Error Amplifier
The error amplifier is a transconductance design, with an
output impedance of 2M
. Since all voltage gain takes
place at the output pin, the open-loop gain/frequency
characteristics can be controlled with shunt reactance to
ground. When compensated for unity-gain stability with
100pF, the amplifier has an open-loop pole at 800Hz.
The input connections to the error amplifier are deter-
mined by the polarity of the switching supply output volt-
age. For positive supplies, the common-mode voltage is
+5.0V and the feedback connections in Figure 6A are
used. With negative supplies, the common-mode voltage
is ground and the feedback divider is connected between
the negative output and the +5.0V reference voltage, as
shown in Figure 6B.
Output Drivers
The totem-pole output drivers of the UC1526 are de-
signed to source and sink 100mA continuously and
200mA peak. Loads can be driven either from the output
pins 13 and 16, or from the +V
C
, as required.
Since the bottom transistor of the totem-pole is allowed to
saturate, there is a momentary conduction path from the
+V
C
terminal to ground during switching. To limit the re-
sulting current spikes a small resistor in series with pin 14
is always recommended. The resistor value is deter-
mined by the driver supply voltage, and should be chosen
for 200mA peak currents.
UC1526
UC2526
UC3526
Figure 5.
Oscillator Connections and Waveforms
Figure 4.
Digital Control Port Schematic
APPLICATIONS INFORMATION (cont.)
5
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| UC2526J | LOW POWER VOLTAGE REGULATOR |
| UC2526L | Low drop voltage regulator |
| UC2526N | Low drop voltage regulator |
| UC2526Q | Low drop voltage regulator |
| UC2526QTR | 5V, 500mA low drop voltage regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UC2526DWTRG4 | 制造商:Texas Instruments 功能描述:VOLT MODE PWM CNTRLR 100MA 18SOIC - Tape and Reel |
| UC2526J | 制造商:Texas Instruments 功能描述:Voltage Mode PWM Controller 100mA 18-Pin CDIP Tube 制造商:Rochester Electronics LLC 功能描述:REG PULSE WIDTH MOD - Bulk |
| UC2526L | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller |
| UC2526N | 功能描述:電壓模式 PWM 控制器 Regulating Pulse Width Modulator RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| UC2526NG4 | 功能描述:電壓模式 PWM 控制器 Regulating Pulse Width Modulator RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。