- 您現在的位置：買賣IC網 > PDF目錄382703 > U4222B Radio Controlled Clock Receiver PDF資料下載
參數資料
| 型號： | U4222B |
| 英文描述： | Radio Controlled Clock Receiver |
| 中文描述： | 電波鐘接收器 |
| 文件頁數： | 4/9頁 |
| 文件大?。?/td> | 98K |
| 代理商： | U4222B |
TELEFUNKEN Semiconductors
U4222B
Preliminary Information
Rev. A1: 07.08.1995
4 (9)
There is some consideration concerning the calculation of
R
res
:
in order to achieve high signal voltage:
R
res
should be high
in order to achieve low antenna noise voltage:
R
res
should be low
R
res
< 200 k :
the input noise voltage of A 1 dominates
R
res
> 300 k :
the antenna noise voltage dominates
That means the resonant resistance should be between
200 k
and 300 k
Q of antenna must be high for attenuation of interfering
signals. But the temperature must not influence the
resonance frequency.
Design Hints for the Ferrite Antenna
The bar antenna is the most critical device of the complete
clock receiver. But by observing some basic rf design
knowledge, no problem should arise with this part. The IC
requires a resonance resistance of 200 k to 300 k . This
can be achieved by a variation of the L/C-relation in the
antenna circuit. But it is not easy to measure such high
resistances in the RF region. It is much more convenient
to distinguish the bandwidth of the antenna circuit and
afterwards to calculate the resonance resistance.
Thus the first step in designing the antenna circuit is to
measure the bandwidth. Figure 4. shows an example for
the test circuit. The RF signal is coupled into the bar
antenna by inductive means, e.g. a wire loop. It can be
measured by a simple oscilloscope using the 10:1 probe.
The input capacitance of the probe, typically about 10 pF,
should be taken into consideration. By varying the
frequency of the signal generator, the resonance
frequency can be determined.
Scope
RF - Signal
generator
40 kHz
C
res
Probe
10 : 1
wire loop
94 8049 e
Figure 4.
Afterwards, the two frequencies where the voltage of the
RF signal at the probe drops 3 dB down can be measured.
The difference between these two frequencies is called
the bandwidth BW
A
of the antenna circuit. As the value
of the capacitor C
res
in the antenna circuit is well known,
it is easy to compute the resonance resistance according
to the following formula:
R
res
1
BW
A
2
C
res
whereas
R
res
is the resonance resistance,
BW
A
is the measured bandwidth (in Hz)
C
res
is the value of the capacitor in the antenna circuit
(in Farad)
If high inductance values and low capacitor values are
used, the additional parasitic capacitances of the coil
must be considered. It may reach up to about 20 pF. The
Q-value of the capacitor should be no problem if a high
Q-type is used. The Q-value of the coil is more or less
distinguished by the simple DC-resistance of the wire.
Skin effects can be observed but do not dominate.
Therefore it should be no problem to achieve the
recommended values of resonance resistance. The use of
thicker wire increases Q and accordingly reduces
bandwidth. This is advantageous in order to improve
reception in noisy areas. On the other hand, temperature
compensation of the resonance frequency might become
a problem if the bandwidth of the antenna circuit is low
compared to the temperature variation of the resonance
frequency. Of course, Q can also be reduced by a parallel
resistor.
Temperature compensation of the resonance frequency is
a must if the clock is used at different temperatures.
Please ask your dealer of bar antenna material and of
capacitors for specified values of temperature coefficient.
Furthermore some critical parasitics have to be
considered. These are shortened loops (e.g. in the ground
line of the PCB board) close to the antenna and undesired
loops in the antenna circuit. Shortened loops decrease Q
of the circuit. They have the same effect like conducting
plates close to the antenna. To avoid undesired loops in
the antenna circuit it is recommended to mount the
capacitor C
res
as close as possible to the antenna coil or
to use a twisted wire for the antenna coil connection. This
twisted line is also necessary to reduce feedback of noise
from the microprocessor to the IC input. Long connection
lines must be shielded.
For the adjustment of the resonance frequency the
capacitance of the probe and the input capacitance of the
IC are to be taken into account. The alignment should be
done in the final environment. The bandwidth is so low
that metal parts close to the antenna influence the
resonance frequency. The adjustment can be done by
pushing the coil along the bar antenna.
相關PDF資料 |
PDF描述 |
|---|---|
| U4222B-CFPG1 | Radio Controlled Clock Receiver |
| U4223B-BFL | Voltage comparators |
| U4223B-BFS | Voltage comparators |
| U4223B-CFS | Low power quad voltage comparator |
| U4223B-CFSG3 | Remote-Control Receiver/Decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| U4222B-CFP | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Radio Controlled Clock Receiver |
| U4222B-CFPG1 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Radio Controlled Clock Receiver |
| U4223B | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Time-Code Receiver with A/D Converter |
| U4223B-BFL | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| U4223B-BFS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
發布緊急采購，3分鐘左右您將得到回復。