- 您現在的位置：買賣IC網 > PDF目錄382702 > U211B3 Phase Control Circuit - General Purpose Feedback PDF資料下載
參數資料
| 型號： | U211B3 |
| 英文描述： | Phase Control Circuit - General Purpose Feedback |
| 中文描述： | 相位控制電路-通用信息反饋 |
| 文件頁數： | 4/20頁 |
| 文件大?。?/td> | 322K |
| 代理商： | U211B3 |
U211B2/ B3
TELEFUNKEN Semiconductors
Rev. A1, 29-May-96
4 (20)
V
C3
t
V
12
V
0
t
1
t
tot
t
2
t
3
95 10272
Figure 4. Soft-start
t
1
t
2
t
1
+ t
2
= dead time
t
3
= run-up time
t
tot
= total start-up time to required speed
C
3
is first charged up to the starting voltage V
0
with
typical 45 A current (t
2
). By then reducing the charging
current to approx. 4 A, the slope of the charging function
is substantially reduced so that the rotational speed of the
motor only slowly increases. The charging current then
increases as the voltage across C
3
increases giving a
progressively rising charging function which accelerates
the motor more and more strongly with increasing
rotational speed. The charging function determines the
acceleration up to the set-point. The charging current can
have a maximum value of 55 A.
Frequency to Voltage Converter
= build-up of supply voltage
= charging of C
3
to starting voltage
The internal frequency to voltage converter (f/V-
converter) generates a DC signal on Pin 10 which is
proportional to the rotational speed using an AC signal
from a tacho-generator or a light beam whose frequency
is in turn dependent on the rotational speed. The high
impedance input Pin 8, compares the tacho-voltage to a
switch-on threshold of typ. –100 mV. The switch-off
threshold is given with –50 mV. The hysteresis
guarantees very reliable operation even when relatively
simple tacho-generators are used. The tacho-frequency is
given by:
n
60
f
p (Hz)
where:
n = revolutions per minute
p = number of pulses per revolution
The converter is based on the charge pumping principle.
With each negative half wave of the input signal, a
quantity of charge determined by C
5
is internally
amplified and then integrated by C
6
at the converter
output on Pin 10. The conversion constant is determined
by C
5
, its charge transfer voltage of V
ch
, R
6
(Pin 10) and
the internally adjusted charge transfer gain.
k = G
i
C
5
R
6
V
ch
G
i
I
10
I
9
8.3
The analog output voltage is given by
V
O
= k f
The values of C
5
and C
6
must be such that for the highest
possible input frequency, the maximum output voltage
V
O
does not exceed 6 V. While C
5
is charging up, the R
i
on Pin 9 is .approx. 6.7 k . To obtain good linearity of the
f/V converter the time constant resulting from R
i
and C
5
should be considerably less (1/5) than the time span of the
negative half-cycle for the highest possible input
frequency. The amount of remaining ripple on the output
voltage on Pin 10
is dependent on C
5
, C
6
and the internal
charge amplification.
V
O
=
G
i
V
ch
C
6
C
5
The ripple
V
o
can be reduced by using larger values of
C
6
. However, the increasing speed will then also be
reduced.
The value of this capacitor should be chosen to fit the
particular control loop where it is going to be used.
Pulse Blocking
The output of pulses can be blocked using Pin 18 (standby
operation) and the system reset via the voltage monitor if
V
18
≥
–1.25
V. After cycling through the switching point
hysteresis, the output is released when V
18
≤
–1.5 V
followed by a soft-start such as that after turn on.
Monitoring of the rotation can be carried out by
connecting an RC network to Pin 18. In the event of a
short or open circuit, the triac triggering pulses are cut off
by the time delay which is determined by R and C. The
capacitor C is discharged via an internal resistance
R
i
= 2 k with each charge transfer process of the f/V
converter. If there are no more charge transfer processes
C is charged up via R until the switch-off threshold is
exceeded and the triac triggering pulses are cut off. For
operation without trigger pulse blocking or monitoring of
the rotation, Pins 18
and 16 must be connected together.
相關PDF資料 |
PDF描述 |
|---|---|
| U2270B | Read / Write Base Station IC |
| U2305B | VHF/ UHF-Tuner-IC |
| U2305B-AFSG3 | VHF/ UHF-Tuner-IC |
| U2320B | VHF/UHF Tuner-IC |
| U2320B-FLG3 | VHF/UHF Tuner-IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| U211B-M | 功能描述:IC PHASE CONTROL TACHO 18-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 產品變化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 標準包裝:1 系列:- 應用:DC 電機控制器，無刷（BLDC），3 相 評估套件:可供 輸出數:1 電流 - 輸出:100mA 電壓 - 負載:5.25 V ~ 20 V 電源電壓:5.25 V ~ 20 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-VQFN（7x7） 包裝:剪切帶 (CT) 其它名稱:ATA6833-PLQWCT |
| U211B-MFP | 功能描述:IC PHASE CONTROL TACHO 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 產品變化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 標準包裝:1 系列:- 應用:DC 電機控制器，無刷（BLDC），3 相 評估套件:可供 輸出數:1 電流 - 輸出:100mA 電壓 - 負載:5.25 V ~ 20 V 電源電壓:5.25 V ~ 20 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-VQFN（7x7） 包裝:剪切帶 (CT) 其它名稱:ATA6833-PLQWCT |
| U211B-MFPG3 | 功能描述:IC PHASE CONTROL TACHO 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| U211B-MFPG3Y | 功能描述:馬達/運動/點火控制器和驅動器 Phase Sw/Control w/ Tacho overld limit RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| U211B-MFPY | 功能描述:馬達/運動/點火控制器和驅動器 Phase Sw/Control w/ Tacho overld limit RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。