- 您現在的位置：買賣IC網 > PDF目錄385026 > TSOP1840XG1 (Vishay Intertechnology,Inc.) Photo Modules for PCM Remote Control Systems PDF資料下載
參數資料
| 型號： | TSOP1840XG1 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Photo Modules for PCM Remote Control Systems |
| 中文描述： | 圖片模塊PCM的遠程控制系統 |
| 文件頁數： | 3/7頁 |
| 文件大小： | 97K |
| 代理商： | TSOP1840XG1 |
TSOP18..QJ1
Vishay Telefunken
3 (7)
Rev. 4, 05-Jun-00
www.vishay.de
FaxBack +1-408-970-5600
Document Number 82049
Suitable Data Format
The circuit of the TSOP18..QJ1 is designed in that way
that unexpected output pulses due to noise or
disturbance signals are avoided. A bandpassfilter, an
integrator stage and an automatic gain control are
used to suppress such disturbances.
The distinguishing mark between data signal ( not
suppressed) and disturbance signal (supressed) are
carrier frequency, burst length and Signal Gap Time
(see diagram below).
The data signal should fullfill the following condition:
Carrier frequency should be close to center fre-
quency of the bandpass (e.g. 38kHz).
Burst length should be 6 cycles/burst or longer.
After each burst a gap time of at least 9 cycles is
neccessary.
The data format should not make a continuous
signal transmission. There must be a Signal Gap Time
(longer than 15ms) at least each 90ms (see Figure A)
Some examples for suitable data format are:
NEC Code (repetitive pulse), NEC Code (repetitive
data), Toshiba Micom Format, Sharp Code, RC5
Code, RECS–80 Code, R–2000 Code.
When a disturbance signal is applied to the
TSOP18..QJ1 it can still receive the data signal.
However the sensitivity is reduced to that level that no
unexpected pulses will occure.
Some examples for such disturbance signals which
are suppressed by the TSOP18..QJ1 are:
DC light (e.g. from tungsten bulb or sunlight),
frequency,
Continuous signal at 38kHz or at any other
Signals from fluorescent lamps (see Figure B)
Continuous IR signal (e.g. 1ms burst, 2ms pause)
0
10
20
30
40
50
60
70
80
90
100
time [ms]
Signal Gap Time
Figure A: Data Signal (Output of IR Receiver) with a Signal Gap Time of 20ms
0
2
4
6
8
10
12
14
16
18
20
time [ms]
Signal Gap Time
Figure B: Disturbance Signal from Fluorescent Lamp with Signal Gap Time of 7ms
(suppressed by TSOP18..)
相關PDF資料 |
PDF描述 |
|---|---|
| TSOP1837QJ1 | DIODE ZENER SINGLE 150mW 10Vz 5mA-Izt 0.06 0.2uA-Ir 7 SOT-523 3K/REEL |
| TSOP1837WE1 | DIODE ZENER SINGLE 200mW 5.6Vz 5mA-Izt 0.0714 1uA-Ir 2 SOT-323 3K/REEL |
| TSOP1838QJ1 | Photo Modules for PCM Remote Control Systems |
| TSOP1838SA1 | RECT BRIDGE GPP 100V 25A GBJ |
| TSOP1838UH1 | RECTIFIER BRIDGE 25A 200V 300A-ifsm 1.1V-vf 5uA-ir GBPCW 100/TRAY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSOP1840YA1 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Photo Modules for PCM Remote Control Systems |
| TSOP1840ZC1 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Photo Modules for PCM Remote Control Systems |
| TSOP1856 | 功能描述:紅外接收機 IR REMOTE SYSTEM RoHS:否 制造商:Vishay Semiconductors 載頻:20 kHz to 60 kHz 傳輸距離:5 m 顯示角:+/- 50 deg 高電平脈沖寬度: 低電平脈沖寬度: 最小高電平輸出電壓: 輸出電流:5 mA 工作電壓:2.5 V to 5.5 V 電源電流:0.9 mA 功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝 / 箱體: 封裝:Reel |
| TSOP1856ON | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:OPTOELECTRONIC CONTROLLER |
| TSOP1856ON1 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Photo Modules for PCM Remote Control Systems |
發布緊急采購，3分鐘左右您將得到回復。