參數資料
型號: TSM105L
廠商: 意法半導體
元件分類: 基準電壓源/電流源
英文描述: CONSTANT VOLTAGE AND CONSTANT CURRENT CONTROLLER FOR BATTERY CHARGERS AND ADAPTORS
中文描述: 恒壓恒流控制器,用于電池充電器及火牛
文件頁數: 5/9頁
文件大?。?/td> 95K
代理商: TSM105L
5/9
1. Voltage and Current Control
1.1. Voltage Control
The voltage loop is controlled via a first transcon-
ductance operational amplifier, the resistor bridge
R1, R2, and the optocoupler which is directly con-
nected to the output.
The relation between the values of R1 and R2
should be chosen as writen in Equation 1.
R1 = R2 x Vref / (Vout - Vref) Eq1
where Vout is the desired output voltage.
To avoid the discharge of the load, the resistor
bridge R1, R2 should be highly resistive. For this
type of application, a total value of 100K
(or
more) would be appropriate for the resistors R1
and R2.
As an example, with R2 = 100K
, Vout = 4.10V,
Vref = 1.210V, then R1 = 41.9K
.
Note that if the low drop diode should be inserted
between the load and the voltage regulation resis-
tor bridge to avoid current flowing from the load
through the resistor bridge, this drop should be
taken into account in the above calculations by re-
placing Vout by (Vout + Vdrop).
1.2. Current Control
The current loop is controlled via the second
trans-conductance operational amplifier, the
sense resistor Rsense, and the optocoupler.
The control equation verifies:
Rsense x Ilim = Vsense eq2
Rsense = Vsense / Ilim eq2’
where Ilim is the desired limited current, and
Vsense is the threshold voltage for the current
control loop.
As an example, with Ilim = 1A, Vsense = -200mV,
then Rsense = 200m
.
Note that the Rsense resistor should be chosen
taking into account the maximum dissipation
(Plim) through it during full load operation.
Plim = Vsense x Ilim. eq3
As an example, with Ilim = 1A, and Vsense =
200mV, Plim = 200mW.
Therefore, for most adapter and battery charger
applications, a quarter-watt, or half-watt resistor to
make the current sensing function is sufficient.
Vsense threshold is achieved internally by a re-
sistor bridge tied to the Vref voltage reference. Its
middle point is tied to the positive input of the cur-
rent control operational amplifier, and its foot is to
be connected to lower potential point of the sense
resistor as shown on the following figure. The re-
sistors of this bridge are matched to provide the
best precision possible
The current sinking outputs of the two trans-con-
nuctance operational amplifiers are common (to
the output of the IC). This makes an ORing func-
tion which ensures that whenever the current or
the voltage reaches too high values, the optocou-
pler is activated.
The relation between the controlled current and
the controlled output voltage can be described
with a square characteristic as shown in the fol-
lowing V/I output-power graph.
Figure 3 :
Output voltage versus output current
2. Compensation
The voltage-control trans-conductance operation-
al amplifier can be fully compensated. Both its out-
put and the negative input are directly accessible
for external compensation components.
Vout
Iout
Voltage regulation
C
TSM105 Vcc : independent power supply
Secondary current regulation
0
TSM105 Vcc : On power output
Primary current regulation
TSM105
PRINCIPLE OF OPERATION AND APPLICATION HINTS
相關PDF資料
PDF描述
TSM108 AUTOMOTIVE SWITCH MODE VOLTAGE AND CURRENT CONTROLLER
TSM108D AUTOMOTIVE SWITCH MODE VOLTAGE AND CURRENT CONTROLLER
TSM108I AUTOMOTIVE SWITCH MODE VOLTAGE AND CURRENT CONTROLLER
TSM108ID AUTOMOTIVE SWITCH MODE VOLTAGE AND CURRENT CONTROLLER
TSM109 DUAL COMPARATOR AND VOLTAGE REFERENCE
相關代理商/技術參數
參數描述
TSM-105-L-DV-LC-P 制造商:Samtec Inc 功能描述:SMT .025" SQUARE POST HEADER .100 CENTERLINE - Bulk
TSM106 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Dual Operational Amplifier and Voltage Reference
TSM-106 -02-S-DV-P-TR 制造商:Samtec Inc 功能描述:CONN UNSHRD HDR HDR 12 POS 2.54MM SLDR ST SMD - Tape and Reel
TSM-106-01-F-DH 制造商:Samtec Inc 功能描述:.025 SQ. TERMINAL STRIPS - Bulk
TSM-106-01-F-DH-A 制造商:Samtec Inc 功能描述:CONN UNSHRD HDR HDR 12 POS 2.54MM SLDR RA SMD - Bulk