參數資料
型號： TSC2008TRGVRQ1
廠商： TEXAS INSTRUMENTS INC
元件分類： 消費家電
英文描述： SPECIALTY CONSUMER CIRCUIT, PQCC16
封裝： 4 X 4 MM, PLASTIC, VQFN-16
文件頁數： 5/35頁
文件大?。?/td> 418K
代理商： TSC2008TRGVRQ1
ConductiveBar
InsulatingMaterial(Glass)
Silver
Ink
TransparentConductor(ITO)
BottomSide
Transparent
Conductor(ITO)
TopSide
X+
X-
Y+
Y-
ITO=IndiumTinOxide
R
TOUCH
+ RXplate @
X
Postition
4096
Z
2
Z
1
* 1
SBAS552
– JUNE 2011
TOUCH SCREEN OPERATION
A resistive touch screen operates by applying a voltage across a resistor network and measuring the change in
resistance at a given point on the matrix where the screen is touched by an input (stylus, pen, or finger). The
change in the resistance ratio marks the location on the touch screen.
The TSC2008-Q1 supports resistive 4-wire configurations, as shown in Figure 22. The circuit determines location
in two coordinate pair dimensions, although a third dimension can be added for measuring pressure.
4-WIRE TOUCH SCREEN COORDINATE PAIR MEASUREMENT
A 4-wire touch screen is typically constructed as shown in Figure 22. It consists of two transparent resistive
layers separated by insulating spacers.
Figure 22. 4-Wire Touch Screen Construction
The 4-wire touch screen panel works by applying a voltage across the vertical or horizontal resistive network.
The A/D converter converts the voltage measured at the point where the panel is touched. A measurement of the
Y position of the pointing device is made by connecting the X+ input to a data converter chip, turning on the Y+
and Y
– drivers, and digitizing the voltage seen at the X+ input. The voltage measured is determined by the
voltage divider developed at the point of touch. For this measurement, the horizontal panel resistance in the X+
lead does not affect the conversion because of the high input impedance of the A/D converter.
Voltage is then applied to the other axis, and the A/D converter converts the voltage representing the X position
on the screen. This process provides the X and Y coordinates to the associated processor.
Measuring touch pressure (Z) can also be done with the TSC2008-Q1. To determine pen or finger touch, the
pressure of the touch must be determined. Generally, it is not necessary to have very high performance for this
test; therefore, 8-bit resolution mode may be sufficient (however, data sheet calculations are shown using 12-bit
resolution mode). There are several different ways of performing this measurement. The TSC2008-Q1 supports
two methods. The first method requires knowing the X-plate resistance, the measurement of the X-Position, and
two additional cross panel measurements (Z2 and Z1) of the touch screen (see Figure 23). Equation 1 calculates
the touch resistance:
(1)
Copyright
2011, Texas Instruments Incorporated
13
相關PDF資料
PDF描述
TSC2046EIPWG4 SPECIALTY CONSUMER CIRCUIT, PDSO16
TSC2046IGQCR SPECIALTY CONSUMER CIRCUIT, PBGA48
TSC2046IPWR SPECIALTY CONSUMER CIRCUIT, PDSO16
TSC2046IPW SPECIALTY CONSUMER CIRCUIT, PDSO16
TSC2046IRGVR SPECIALTY CONSUMER CIRCUIT, PQCC16
相關代理商/技術參數
參數描述
TSC2011 制造商:TI 制造商全稱:Texas Instruments 功能描述:Nanopower, 4-Wire Resistive Touch and Haptic Controller with I2Ca?￠ Serial Interface
TSC2011IRTJR 制造商:TI 制造商全稱:Texas Instruments 功能描述:Nanopower, 4-Wire Resistive Touch and Haptic Controller with I2Ca?￠ Serial Interface
TSC2011IRTJT 制造商:TI 制造商全稱:Texas Instruments 功能描述:Nanopower, 4-Wire Resistive Touch and Haptic Controller with I2Ca?￠ Serial Interface
TSC2011IYZKR 制造商:TI 制造商全稱:Texas Instruments 功能描述:Nanopower, 4-Wire Resistive Touch and Haptic Controller with I2Ca?￠ Serial Interface
TSC2011IYZKT 制造商:TI 制造商全稱:Texas Instruments 功能描述:Nanopower, 4-Wire Resistive Touch and Haptic Controller with I2Ca?￠ Serial Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*