參數資料
型號: TSA1204IFT
廠商: STMICROELECTRONICS
元件分類: ADC
英文描述: 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48
封裝: 7 X 7 MM, PLASTIC, TQFP-48
文件頁數: 19/21頁
文件大小: 498K
代理商: TSA1204IFT
TSA1204
7/21
DEFINITIONS OF SPECIFIED PARAMETERS
STATIC PARAMETERS
Static measurements are performed through
method of histograms on a 2MHz input signal,
sampled at 20Msps, which is high enough to fully
characterize the test frequency response. The
input level is +1dBFS to saturate the signal.
Differential Non Linearity (DNL)
The average deviation of any output code width
from the ideal code width of 1 LSB.
Integral Non linearity (INL)
An ideal converter presents a transfer function as
being the straight line from the starting code to the
ending code. The INL is the deviation for each
transition from this ideal curve.
DYNAMIC PARAMETERS
Dynamic
measurements
are
performed
by
spectral analysis, applied to an input sine wave of
various frequencies and sampled at 20Msps.
The input level is -1dBFS to measure the linear
behavior of the converter. All the parameters are
given without correction for the full scale ampli-
tude performance except the calculated ENOB
parameter.
Spurious Free Dynamic Range (SFDR)
The ratio between the power of the worst spurious
signal (not always an harmonic) and the amplitude
of fundamental tone (signal power) over the full
Nyquist band. It is expressed in dBc.
Total Harmonic Distortion (THD)
The ratio of the rms sum of the first five harmonic
distortion components to the rms value of the
fundamental line. It is expressed in dB.
Signal to Noise Ratio (SNR)
The ratio of the rms value of the fundamental
component to the rms sum of all other spectral
components in the Nyquist band (fs/2) excluding
DC, fundamental and the first five harmonics.
SNR is reported in dB.
Signal to Noise and Distortion Ratio (SINAD)
Similar ratio as for SNR but including the harmonic
distortion components in the noise figure (not DC
signal). It is expressed in dB.
From the SINAD, the Effective Number of Bits
(ENOB) can easily be deduced using the formula:
SINAD= 6.02
× ENOB + 1.76 dB.
When the applied signal is not Full Scale (FS), but
has an A0 amplitude, the SINAD expression
becomes:
SINAD2Ao=SINADFull Scale+ 20 log (2A0/FS)
SINAD2Ao=6.02 × ENOB + 1.76 dB + 20 log (2A0/
FS)
The ENOB is expressed in bits.
Analog Input Bandwidth
The maximum analog input frequency at which the
spectral response of a full power signal is reduced
by 3dB. Higher values can be achieved with
smaller input levels.
Effective Resolution Bandwidth (ERB)
The band of input signal frequencies that the ADC
is intended to convert without loosing linearity i.e.
the maximum analog input frequency at which the
SINAD is decreased by 3dB or the ENOB by 1/2
bit.
Pipeline delay
Delay between the initial sample of the analog
input and the availability of the corresponding
digital data output, on the output bus. Also called
data latency. It is expressed as a number of clock
cycles.
相關PDF資料
PDF描述
TSA1204IF 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48
TSA1401IF 1-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48
TSA1401IFT 1-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48
TSA5522TD-T PLL FREQUENCY SYNTHESIZER, 1400 MHz, PDSO16
TSC2003IPWRQ1 SPECIALTY CONSUMER CIRCUIT, PDSO16
相關代理商/技術參數
參數描述
TSA1204IFT-E 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Dual channel 12-bit 20Msps 120mW A/D converter
TSA13 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EURO TERMINAL BLOCKS
TSA14 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EURO TERMINAL BLOCKS
TSA1401 制造商:STMicroelectronics 功能描述:OBS COMM TO USE AS PROTO'S FOR SPACE APPLICATIONS - Bulk
TSA1401IF 功能描述:IC ADC 14BIT 20MSPS 85MW 48TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率(每秒):3M 數據接口:- 轉換器數目:- 功率耗散(最大):- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-