參數資料
型號: TSA1201IFT
廠商: STMICROELECTRONICS
元件分類: ADC
英文描述: 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48
封裝: 7 X 7 MM, PLASTIC, TQFP-48
文件頁數: 19/20頁
文件大?。?/td> 349K
代理商: TSA1201IFT
TSA1201
8/20
DEFINITIONS OF SPECIFIED PARAMETERS
STATIC PARAMETERS
Static measurements are performed through
method of histograms on a 2MHz input signal,
sampled at 50Msps, which is high enough to fully
characterize the test frequency response. The
input level is +1dBFS to saturate the signal.
Differential Non Linearity (DNL)
The average deviation of any output code width
from the ideal code width of 1LSB.
Integral Non linearity (INL)
An ideal converter presents a transfer function as
being the straight line from the starting code to the
ending code. The INL is the deviation for each
transition from this ideal curve.
DYNAMIC PARAMETERS
Dynamic
measurements
are
performed
by
spectral analysis, applied to an input sinewave of
various frequencies and sampled at 50Msps.
Spurious Free Dynamic Range (SFDR)
The ratio between the power of the worst spurious
signal (not always an harmonic) and the amplitude
of fundamental tone (signal power) over the full
Nyquist band. It is expressed in dBc.
Total Harmonic Distortion (THD)
The ratio of the rms sum of the first five harmonic
distortion components to the rms value of the
fundamental line. It is expressed in dB.
Signal to Noise Ratio (SNR)
The ratio of the rms value of the fundamental
component to the rms sum of all other spectral
components in the Nyquist band (fs/2) excluding
DC, fundamental and the first five harmonics.
SNR is reported in dB.
Signal to Noise and Distortion Ratio (SINAD)
Similar ratio as for SNR but including the harmonic
distortion components in the noise figure (not DC
signal). It is expressed in dB.
From the SINAD, the Effective Number of Bits
(ENOB) can easily be deduced using the formula:
SINAD= 6.02
× ENOB + 1.76 dB.
When the applied signal is not Full Scale (FS), but
has an A0 amplitude, the SINAD expression
becomes:
SINAD= 6.02
× ENOB + 1.76 dB + 20 log (2A
0/FS)
The ENOB is expressed in bits.
Analog Input Bandwidth
The maximum analog input frequency at which the
spectral response of a full power signal is reduced
by 3dB. Higher values can be achieved with
smaller input levels.
Effective Resolution Bandwidth (ERB)
The band of input signal frequencies that the ADC
is intended to convert without loosing linearity i.e.
the maximum analog input frequency at which the
SINAD is decreased by 3dB or the ENOB by 1/2
bit.
Pipeline delay
Delay between the initial sample of the analog
input and the availability of the corresponding
digital data output,on the output bus. Also called
data latency. It is expressed as a number of clock
cycles.
相關PDF資料
PDF描述
TSA1203IFT 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, QFP48
TSA1203IF 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, QFP48
TSA1203IFT-E 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, QFP48
TSA1204IFT-E 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48
TSA1204IFT 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48
相關代理商/技術參數
參數描述
TSA1203 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DUAL-CHANNEL, 12-BIT, 40MSPS, 230mW A/D CONVERTER
TSA1203_06 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Dual-channel 12-bit 40Msps 215mW A/D converter
TSA1203IF 功能描述:模數轉換器 - ADC Dual Channel 12-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TSA1203IFT 功能描述:模數轉換器 - ADC Dual Channel 12-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TSA1203IFT-E 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Dual-channel 12-bit 40Msps 215mW A/D converter