
TS5214
300mA Low Noise LDO Voltage Regulator
Absolute Maximum Rating
(Note 1)
Parameter
Input Supply Voltage
Input Supply Voltage (Recommend)
Power Dissipation (Note 2)
2/7
Version: C07
Symbol
V
IN
V
IN
P
D
Limit
-20~ +20
+2.5 ~ +16
Internal limited
220
180
130
-40 ~ +125
-65 ~ +150
5
Unit
V
V
SOT-23
SOT-89
SOT-223
Thermal Resistance
JA
o
C/W
Operating Junction Temperature Range
Storage Temperature Range
Lead Soldering Temperature (260
o
C)
T
J
T
STG
o
C
o
C
S
Electrical Specification
(
V
IN
=Vo+1V, Io=100uA, C
OUT
=1uF, Vce
≥
2V, T
J
= 25
o
C, unless otherwise specified.)
Parameter
Conditions
V
IN
=Vo + 1V
Output Voltage
V
IN
=Vo + 1V, Io= 120mA
Output Voltage Temp. Coefficient
(Note 4)
Line Regulation
Vo+1V
≤
V
IN
≤
16V
Load Regulation (Note 5)
0.1mA
≤
Io
≤
120mA
Io=100uA
Io=50mA
Io=150mA
Io=300mA (5V version)
Io=100uA
Io=50mA
Io=150mA
Io=300mA (5V version)
Output Current Limit
V
OUT
=0V
Power Supply Rejection Ratio
At f=100Hz, Io=100uA,
Thermal Regulation (Note 8)
Output Noise
Io=50mA, C
OUT
=2.2uF,
Note:
1. Exceeding the absolute maximum rating may damage the device.
2. The maximum allowable power dissipation at any Ta is Pd(max) = [T
J
(max) - Ta] +
JA
. Exceeding the maximum
allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown.
3. The device is not guaranteed to function outside its operating rating.
4: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature
range.
5: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for
load regulation in the load range from 1mA to 300mA (5V version) and 1mA to 120mA (V
OUT
<5V version). Changes
in output voltage due to heating effects are covered by the thermal regulation specification.
6: Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal
value measured at 1V differential.
7: Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from
the supply is the sum of the load current plus the ground pin current.
8: Thermal regulation is defined as the change in output voltage at a time “t” after a change in power dissipation is
applied, excluding load or line regulation effects. Specifications are for a 300mA load pulse at Vin=16V for t=10mS.
Min
0.97|Vo|
0.96|Vo|
--
--
--
--
--
--
--
--
--
--
--
150
--
--
--
Typ
Max
1.03|Vo|
1.04|Vo|
--
0.5
2
--
300
400
500
150
1000
3100
4200
--
--
--
--
Unit
V
OUT
V
50
0.1
1
20
250
350
450
110
500
2600
3500
200
75
0.05
260
ppm/
o
C
%
%
Dropout Voltage (Note 6)
mV
Ground Pin Current (Note 7)
uA
mA
dB
%/W
nV
√
Hz