- 您現在的位置：買賣IC網 > PDF目錄373710 > TS5201_1 (Taiwan Semiconductor Co., Ltd.) 200mA Low Noise LDO Voltage Regulator with Enable PDF資料下載
參數資料
| 型號： | TS5201_1 |
| 廠商： | Taiwan Semiconductor Co., Ltd. |
| 英文描述： | 200mA Low Noise LDO Voltage Regulator with Enable |
| 中文描述： | 200mA低噪聲LDO穩壓器的啟用 |
| 文件頁數： | 5/6頁 |
| 文件大小： | 271K |
| 代理商： | TS5201_1 |
TS5201 series
5-6
2005/08 rev. C
Application Information (continues)
Thermal Characteristics
TS5201 series is designed to provide 200mA of
continuous current in a very small package. Maximum
power dissipation can be calculated based on the
output current and the voltage drop across the part. To
determine the maximum power dissipation of the
package, use the junction-ambient thermal resistance
of the device and the following basic equation:
Pd(max) = [ Tj(max) – Ta ] /
Θ
ja
Tj(max) is the maximum junction temperature of the
die(125
o
C), and Ta is the ambient operating
temperature.
Θ
ja is layout dependent, the actual
power dissipation of the regulator circuit can be
determined using the equation:
Pd = ( Vin – Vout ) * Iout + Vin * Ignd
Substituting Pd(max) for Pd and solving for the
operating conditions that are critical to the application
will give the maximum operating conditions for the
regulator circuit. For example, when operating the
TS5201CX533 at room temperature with a minimum
footprint layout, the maximum input voltage for a set
output current can be determined as follows:
Pd(max) = (125
o
C – 25
o
C) / 220
o
C/W
Pd(max) = 455mW
The junction to ambient thermal resistance for the
minimum footprint is 220
o
C/W, the maximum power
dissipation must not be exceeded for proper operation.
Using the output voltage of 3.3V and an output current
of 200mA, the maximum input voltage can be
determined. Formt eh electrical characteristics table,
the maximum ground current for 200mA output current
is 2.5mA.
445mW = ( Vin – 3.3V ) * 200mA + Vin * 2.5mA
445mW = Vin * 200mA – 3.3 * 200mA + Vin * 2.5mA
445mW = Vin * 200mA – 495mW + Vin * 2.5mA
950mW = Vin * 152.5mA
Vin(max) = 6.23v
Therefore, a 3.3V application at 200mA of output
current can accept a maximum input voltage of 6.23V
in a SOT-25 package.
Noise Reduction Capacitors
On adjustable devices, a capacitor from ADJ to GND
will decrease high frequency noise on the output. See
following figure
Minimum Load
The TS5201 will remain stable and in regulation
with no load unlike many other voltage regulators.
This is especially important in CMOS RAM
keep-alive applications.
Dual-Supply Systems
When used in dual supply systems where the
regulator load is returned to a negative supply, the
output voltage must be diode clamped to ground.
相關PDF資料 |
PDF描述 |
|---|---|
| TS5201CS | 200mA Low Noise LDO Voltage Regulator with Enable |
| TS5204CY2.5 | 150mA Low Noise LDO Voltage Regulator |
| TS5204CY2.8 | 150mA Low Noise LDO Voltage Regulator |
| TS5204CY2.9 | 150mA Low Noise LDO Voltage Regulator |
| TS5204CX5.0 | 150mA Low Noise LDO Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS5201CS | 功能描述:低壓差穩壓器 - LDO 200mA Low Noise LDO Vltg Reg Adj RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TS5201CS RL | 制造商:SKMI/Taiwan 功能描述:SOP-8;200MA LOW NOISE LDO VOLT |
| TS5201CS25 RL | 制造商:SKMI/Taiwan 功能描述:SOP-8;200MA LOW NOISE LDO VOLT |
| TS5201CS30 RL | 制造商:SKMI/Taiwan 功能描述:SOP-8;200MA LOW NOISE LDO VOLT |
| TS5201CS33 RL | 制造商:SKMI/Taiwan 功能描述:SOP-8;200MA LOW NOISE LDO VOLT |
發布緊急采購，3分鐘左右您將得到回復。