- 您現在的位置：買賣IC網 > PDF目錄373710 > TS5201_07 (Taiwan Semiconductor Co., Ltd.) 200mA Low Noise LDO Voltage Regulator with Enable PDF資料下載
參數資料
| 型號： | TS5201_07 |
| 廠商： | Taiwan Semiconductor Co., Ltd. |
| 英文描述： | 200mA Low Noise LDO Voltage Regulator with Enable |
| 中文描述： | 200mA低噪聲LDO穩壓器的啟用 |
| 文件頁數： | 5/7頁 |
| 文件大?。?/td> | 267K |
| 代理商： | TS5201_07 |
TS5201
200mA Low Noise LDO
Voltage Regulator with Enable
Application Information (Continue)
5/7
Version: A07
Dual Supply Operation
When used in dual supply systems where the regulator load is returned to a negative supply, the output voltage must
be diode clamped to ground.
Thermal Characteristics
TS5201 series is designed to provide 200mA (5V version) of continuous current in a very small package. Maximum
power dissipation can be calculated based on the output current and the voltage drop across the part. To determine
the maximum power dissipation of the package, use the junction-ambient thermal resistance of the device and the
following basic equation:
P
D(MAX)
= [ T
J(MAX)
– T
A
] /
Θ
JA
T
J(MAX)
is the maximum junction temperature of the die(125
o
C), and Ta is the ambient operating temperature.
Θ
JA
is
layout dependent, the actual power dissipation of the regulator circuit can be determined using the equation:
P
D
= (V
IN
– V
OUT
) * I
OUT
+ V
IN
* I
GND
Substituting Pd(max) for Pd and solving for the operating conditions that are critical to the application will give the
maximum operating conditions for the regulator circuit. For example, when operating the TS5201CS33 at room
temperature with a minimum footprint layout, the maximum input voltage for a set output current can be determined
as follows:
P
D(MAX)
= (125
o
C – 25
o
C) / 220
o
C/W
P
D(MAX)
= 455mW
The junction to ambient thermal resistance for the minimum footprint is 220
o
C/W, the maximum power dissipation
must not be exceeded for proper operation. Using the output voltage of 3.3V and an output current of 120mA, the
maximum input voltage can be determined. From the electrical characteristics table, the maximum ground current for
120mA output current is 2.5mA.
445mW = (V
IN
– 3.3V ) * 200mA + V
IN
* 2.5mA
445mW = V
IN
* 200mA – 3.3 * 200mA + V
IN
* 2.5mA
445mW = V
IN
* 200mA – 495mW + V
IN
* 2.5mA
950mW = V
IN
* 152.5mA
V
IN
(max) = 6.23V
Therefore, a 3.3V application at 200mA of output current can accept a maximum input voltage of 6.23V in a SOP-8
package.
Noise Reduction Capacitors
On adjustable devices, a capacitor from ADJ to GND will decrease high frequency noise on the output. See following
figure:
Minimum Load
The TS5201 will remain stable and in regulation with no load unlike many other voltage regulators. This is especially
important in CMOS RAM keep-alive applications.
相關PDF資料 |
PDF描述 |
|---|---|
| TS5201 | 200mA Low Noise LDO Voltage Regulator with Enable |
| TS5201_1 | 200mA Low Noise LDO Voltage Regulator with Enable |
| TS5201CS | 200mA Low Noise LDO Voltage Regulator with Enable |
| TS5204CY2.5 | 150mA Low Noise LDO Voltage Regulator |
| TS5204CY2.8 | 150mA Low Noise LDO Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS5201CS | 功能描述:低壓差穩壓器 - LDO 200mA Low Noise LDO Vltg Reg Adj RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TS5201CS RL | 制造商:SKMI/Taiwan 功能描述:SOP-8;200MA LOW NOISE LDO VOLT |
| TS5201CS25 RL | 制造商:SKMI/Taiwan 功能描述:SOP-8;200MA LOW NOISE LDO VOLT |
| TS5201CS30 RL | 制造商:SKMI/Taiwan 功能描述:SOP-8;200MA LOW NOISE LDO VOLT |
| TS5201CS33 RL | 制造商:SKMI/Taiwan 功能描述:SOP-8;200MA LOW NOISE LDO VOLT |
發布緊急采購，3分鐘左右您將得到回復。