- 您現在的位置：買賣IC網 > PDF目錄365930 > TPS76750QDR VOLT REGULATOR|FIXED|+5V|CMOS|SOP|8PIN|PLASTIC PDF資料下載
參數資料
| 型號： | TPS76750QDR |
| 英文描述： | VOLT REGULATOR|FIXED|+5V|CMOS|SOP|8PIN|PLASTIC |
| 中文描述： | 電壓調節器|定額| 5V的|的CMOS |?？苵 8引腳|塑料 |
| 文件頁數： | 14/18頁 |
| 文件大?。?/td> | 329K |
| 代理商： | TPS76750QDR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁
TPS76515, TPS76518, TPS76525, TPS76527
TPS76528, TPS76530, TPS76533, TPS76550, TPS76501
ULTRA-LOW QUIESCIENT CURRENT 150-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS236 – AUGUST 1999
14
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
The TPS765xx family includes eight fixed-output voltage regulators (1.5 V, 1.8 V, 2.5 V, 2.7 V, 2.8 V, 3.0 V,
3.3 V, and 5.0 V), and an adjustable regulator, the TPS76501 (adjustable from 1.25 V to 5.5 V).
device operation
The TPS765xx features very low quiescent current, which remains virtually constant even with varying loads.
Conventional LDO regulators use a pnp pass element, the base current of which is directly proportional to the
load current through the regulator (I
B
= I
C
/
β
). The TPS765xx uses a PMOS transistor to pass current; because
the gate of the PMOS is voltage driven, operating current is low and invariable over the full load range.
Another pitfall associated with the pnp-pass element is its tendency to saturate when the device goes into
dropout. The resulting drop in
β
forces an increase in I
B
to maintain the load. During power up, this translates
to large start-up currents. Systems with limited supply current may fail to start up. In battery-powered systems,
it means rapid battery discharge when the voltage decays below the minimum required for regulation. The
TPS765xx quiescent current remains low even when the regulator drops out, eliminating both problems.
The TPS765xx family also features a shutdown mode that places the output in the high-impedance state
(essentially equal to the feedback-divider resistance) and reduces quiescent current to 1
μ
A (typ). If the
shutdown feature is not used, EN should be tied to ground. Response to an enable transition is quick; regulated
output voltage is reestablished in typically 160
μ
s.
minimum load requirements
The TPS765xx family is stable even at zero load; no minimum load is required for operation.
FB - pin connection (adjustable version only)
The FB pin is an input pin to sense the output voltage and close the loop for the adjustable option . The output
voltage is sensed through a resistor divider network to close the loop as it is shown in Figure 29. Normally, this
connection should be as short as possible; however, the connection can be made near a critical circuit to
improve performance at that point. Internally, FB connects to a high-impedance wide-bandwidth amplifier and
noise pickup feeds through to the regulator output. Routing the FB connection to minimize/avoid noise pickup
is essential.
external capacitor requirements
An input capacitor is not usually required; however, a ceramic bypass capacitor (0.047
μ
F or larger) improves
load transient response and noise rejection if the TPS765xx is located more than a few inches from the power
supply. A higher-capacitance electrolytic capacitor may be necessary if large (hundreds of milliamps) load
transients with fast rise times are anticipated.
Like all low dropout regulators, the TPS765xx requires an output capacitor connected between OUT and GND
to stabilize the internal control loop. The minimum recommended capacitance value is 4.7
μ
F and the ESR
(equivalent series resistance) must be between 300-m
and 20-
. Capacitor values 4.7
μ
F or larger are
acceptable, provided the ESR is less than 20
. Solid tantalum electrolytic, aluminum electrolytic, and multilayer
ceramic capacitors are all suitable, provided they meet the requirements described previously.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| TPS76750QPWPR | VOLT REGULATOR|FIXED|+5V|CMOS|TSSOP|20PIN|PLASTIC |
| TPS767D301PWPR | VOLT REGULATOR|FIXED/ADJUSTABLE|+1.5/5.5V & 3.3V|CMOS|TSSOP|28PIN|PLASTIC |
| TPS767D318PWPR | VOLT REGULATOR|FIXED|+1.8V & +3.3V|CMOS|TSSOP|28PIN|PLASTIC |
| TPS767D325PWPR | THREE-TERMINAL POSITIVE FIXED VOLTAGE REGULATORS |
| TPS76801-EP | Military Enhanced Plastic Fast-Transient-Response 1-A Low-Dropout Voltage Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS76750QDRG4 | 功能描述:低壓差穩壓器 - LDO Fast-Transient Response 1-A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS76750QPWP | 功能描述:低壓差穩壓器 - LDO Fast-Transient Response 1-A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS76750QPWPG4 | 功能描述:低壓差穩壓器 - LDO Fast-Transient Response 1-A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS76750QPWPR | 功能描述:低壓差穩壓器 - LDO Fast-Transient Response 1-A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS76750QPWPREP | 功能描述:低壓差穩壓器 - LDO Mil Enh Fast-Trans Resp 1A LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。