- 您現在的位置：買賣IC網 > PDF目錄382681 > TPS73250DCQT (Texas Instruments, Inc.) Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection PDF資料下載
參數資料
| 型號： | TPS73250DCQT |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| 中文描述： | 無電容，NMOS管，150mA的低壓差穩壓器的反向電流保護 |
| 文件頁數： | 14/18頁 |
| 文件大?。?/td> | 427K |
| 代理商： | TPS73250DCQT |
www.ti.com
dV dt
V
OUT
C
OUT
80k
(R
1
R
2
)
(5)
REVERSE CURRENT
The NMOS pass element of the TPS732xx provides
inherent protection against current flow from the
output of the regulator to the input when the gate of
the pass device is pulled low. To ensure that all
charge is removed from the gate of the pass element,
the enable pin must be driven low before the input
voltage is removed. If this is not done, the pass
element may be left on due to stored charge on the
gate.
POWER DISSIPATION
The ability to remove heat from the die is different for
each package type, presenting different consider-
ations in the PCB layout. The PCB area around the
device that is free of other components moves the
heat from the device to the ambient air. Performance
data for JEDEC low- and high-K boards are shown in
the Power Dissipation Ratings table. Using heavier
copper will increase the effectiveness in removing
heat
from
the
device.
through-holes to heat-dissipating layers will also im-
prove the heat-sink effectiveness.
THERMAL PROTECTION
Thermal protection disables the output when the
junction temperature rises to approximately 160
°
C,
allowing the device to cool. When the junction tem-
perature cools to approximately 140
°
C, the output
circuitry is again enabled. Depending on power dissi-
pation, thermal resistance, and ambient temperature,
the thermal protection circuit may cycle on and off.
This limits the dissipation of the regulator, protecting
it from damage due to overheating.
P
D
(V
IN
V
OUT
)
I
OUT
(6)
Package Mounting
Solder
pad
TPS732xx
Solder Pad Recommendations for Surface-Mount De-
vices
(AB-132), available from the Texas Instruments
web site at www.ti.com.
TPS73201, TPS73215, TPS73216
TPS73218, TPS73225, TPS73230
TPS73233, TPS73250
SBVS037F–AUGUST 2003–REVISED SEPTEMBER 2004
(Adjustable voltage version)
reliability, thermal protection should trigger at least
35
°
C above the maximum expected ambient con-
dition of your application. This produces a worst-case
junction temperature of 125
°
C at the highest ex-
pected ambient temperature and worst-case load.
The internal protection circuitry of the TPS732xx has
been designed to protect against overload conditions.
It was not intended to replace proper heatsinking.
Continuously running the TPS732xx into thermal
shutdown will degrade device reliability.
After the enable pin is driven low, no bias voltage is
needed on any pin for reverse current blocking. Note
that reverse current is specified as the current flowing
out of the IN pin due to voltage applied on the OUT
pin. There will be additional current flowing into the
OUT pin due to the 80k
internal resistor divider to
ground (see Figure 1 and Figure 2).
The
addition
of
plated
For the TPS73201, reverse current may flow when
V
FB
is more than 1.0V above V
IN
.
Power dissipation depends on input voltage and load
conditions. Power dissipation is equal to the product
of the output current times the voltage drop across
the output pass element (V
IN
to V
OUT
):
Power dissipation can be minimized by using the
lowest possible input voltage necessary to assure the
required output voltage.
footprint
are
presented
recommendations
in
Application
for
Bulletin
the
Any tendency to activate the thermal protection circuit
indicates excessive power dissipation or an inad-
equate heatsink. For reliable operation, junction tem-
perature should be limited to 125
°
C maximum. To
estimate the margin of safety in a complete design
(including heatsink), increase the ambient tempera-
ture until the thermal protection is triggered; use
worst-case loads and signal conditions. For good
14
相關PDF資料 |
PDF描述 |
|---|---|
| TPS73215DBVTG4 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| TPS73230DCQG4 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| TPS732XX | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| TPS7348QPW | LOW-DROPOUT VOLTAGE REGULATORS WITH INTEGRATED DELAYED RESET FUNCTION |
| TPS7330QPW | LOW-DROPOUT VOLTAGE REGULATORS WITH INTEGRATED DELAYED RESET FUNCTION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS73250MDBVREP | 功能描述:低壓差穩壓器 - LDO Mil Enh Cap-Free NMOS 250-mA LDO Reg RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS73250QDCQRQ1 | 功能描述:低壓差穩壓器 - LDO AC Cap-Free NMOS 250mA LDO Reg RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS7325QD | 功能描述:低壓差穩壓器 - LDO Low-Dropout Voltage Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS7325QDG4 | 功能描述:低壓差穩壓器 - LDO Low-Dropout Voltage Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS7325QDR | 功能描述:低壓差穩壓器 - LDO Low-Dropout Voltage Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。