- 您現在的位置：買賣IC網 > PDF目錄220090 > TPS62065DSGT (TEXAS INSTRUMENTS INC) 2 A SWITCHING REGULATOR, 3400 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | TPS62065DSGT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 2 A SWITCHING REGULATOR, 3400 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 2 X 2 MM, 0.75 MM HEIGHT, GREEN, PLASTIC, WSON-8 |
| 文件頁數： | 13/28頁 |
| 文件大?。?/td> | 1208K |
| 代理商： | TPS62065DSGT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
V
IN
V
OUT
GND
L
C
IN
C
OUT
R1
R2
C
FF
GND
Enable
Mode/PG
SLVS833A – MARCH 2010 – REVISED MAY 2010
www.ti.com
LAYOUT CONSIDERATIONS
Figure 28. PCB Layout
As for all switching power supplies, the layout is an important step in the design. Proper function of the device
demands careful attention to PCB layout. Care must be taken in board layout to get the specified performance. If
the layout is not carefully done, the regulator could show poor line and/or load regulation, stability issues as well
as EMI and thermal problems. It is critical to provide a low inductance, impedance ground path. Therefore, use
wide and short traces for the main current paths. The input capacitor should be placed as close as possible to
the IC pins as well as the inductor and output capacitor.
Connect the AGND and PGND Pins of the device to the PowerPAD land of the PCB and use this pad as a star
point. Use a common Power PGND node and a different node for the Signal AGND to minimize the effects of
ground noise. The FB divider network should be connected right to the output capacitor and the FB line must be
routed away from noisy components and traces (e.g., SW line).
Due to the small package of this converter and the overall small solution size the thermal performance of the
PCB layout is important. To get a good thermal performance a four or more Layer PCB design is recommended.
The PowerPAD of the IC must be soldered on the power pad area on the PCB to get a proper thermal
connection. For good thermal performance the PowerPAD on the PCB needs to be connected to an inner GND
plane with sufficient via connections. Please refer to the documentation of the evaluation kit.
20
Copyright 2010, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TC151A5122EOA723 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151A5226EOA723 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151B3535EOA713 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151A3536EOA713 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151B5249EOA723 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS62065DSGT | 制造商:Texas Instruments 功能描述:VOLTAGE REGULATOR IC 制造商:Texas Instruments 功能描述:IC, STEP-DOWN CONVERTER, WSON-8 |
| TPS62065QDSGRQ1 | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 2A 8-WFDFN Exposed Pad 制造商:texas instruments 系列:汽車級，AEC-Q100 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:2.9V 電壓 - 輸入（最大值）:6V 電壓 - 輸出（最小值/固定）:0.8V 電壓 - 輸出（最大值）:6V 電流 - 輸出:2A 頻率 - 開關:3MHz 同步整流器:是 工作溫度:-40°C ~ 125°C （TJ） 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商器件封裝:8-WSON（2x2） 標準包裝:1 |
| TPS62067DSGR | 功能描述:直流/直流開關轉換器 3MHz 2A Step-Down Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS62067DSGT | 功能描述:直流/直流開關轉換器 3MHz 2A Step-Down Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS62067DSGT | 制造商:Texas Instruments 功能描述:VOLTAGE REGULATOR IC 制造商:Texas Instruments 功能描述:IC, STEP-DOWN CONVERTER, WSON-8 |
發布緊急采購，3分鐘左右您將得到回復。