- 您現在的位置：買賣IC網 > PDF目錄365926 > TPS61012DGSR Analog IC PDF資料下載
參數資料
| 型號： | TPS61012DGSR |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 14/22頁 |
| 文件大?。?/td> | 392K |
| 代理商： | TPS61012DGSR |
TPS61000, TPS61001, TPS61002, TPS61003, TPS61004, TPS61005, TPS61006, TPS61007
SINGLE-AND DUAL-CELL BOOST CONVERTER WITH START-UP INTO FULL LOAD
SLVS279B – MARCH 2000 – REVISED AUGUST 2000
14
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
The TPS6100x boost converter family is intended for systems that are powered by a single-cell NiCd or NiMH
battery with a typical terminal voltage between 0.9 V to 1.6 V. It can also be used in systems that are powered
by two-cell NiCd or NiMH batteries with a typical stack voltage between 1.8 V and 3.2 V. Additionally, single-
or dual-cell, primary and secondary alkaline battery cells can be the power source in systems where the
TPS6100x is used.
programming the TPS61000 and TPS61007 adjustable output voltage devices
The output voltage of the TPS61000 and TPS61007 can be adjusted with an external resistor divider. The typical
value of the voltage on the FB pin is 500 mV in fixed frequency operation and 485 mV in the power-save
operation mode. The maximum allowed value for the output voltage is 3.3 V. The current through the resistive
divider should be about 100 times greater than the current into the FB pin. The typical current into the FB pin
is 0.01
μ
A, the voltage across R4 is typically 500 mV. Based on those two values, the recommended value for
R4 is in the range of 500 k
in order to set the divider current at 1
μ
A. From that, the value of resistor R3,
depending on the needed output voltage V
OUT
, can be calculated using the following equation:
R3
R4
VO
VFB
1
500 k
VO
500 mV
1
(1)
If, as an example, an output voltage of 2.5 V is needed, a 2-M
resistor should be chosen for R3.
VBAT
VOUT
LBO
5
10
3
R5
R3
R4
6
TPS61007
LBI
9
FB
COMP
2
CC1
100 pF
CC2
33 nF
RC
10 k
EN
R2
R1
1
GND
SW
7
4
Ci
10
μ
F
10 V
CO
22
μ
F
10 V
Low Battery
Warning
L1
33
μ
H
D1
FBGND
8
VO
Alkaline Cell
Figure 18. Typical Application Circuit for Adjustable Output Voltage Option
The TPS61007 is an improved version of the TPS61000 adjustable output voltage device.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS61013DGSR | Analog IC |
| TPS61014DGSR | Analog IC |
| TPS61015DGSR | Analog IC |
| TPS61016DGSR | Analog IC |
| TPS61040DBVT | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS61012DGSRG4 | 功能描述:直流/直流開關調節器 Lo-In Voltage Sync Boost Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS61013 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:HIGH-EFFICIENCY, 1-CELL AND 2-CELL BOOST CONVERTERS |
| TPS61013DGS | 功能描述:直流/直流開關調節器 Lo-In Voltage Sync Boost Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS61013DGSG4 | 功能描述:直流/直流開關調節器 Lo-In Voltage Sync Boost Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS61013DGSR | 功能描述:開關變換器、穩壓器與控制器 Lo-In Voltage Sync Boost Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。