參數資料
型號： TPS56302PWPR
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： 2 A DUAL SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO28
封裝： GREEN, POWERPAD, PLASTIC, TSSOP-28
文件頁數： 5/37頁
文件大?。?/td> 1017K
代理商： TPS56302PWPR
TPS56302
DUALOUTPUT LOW INPUT VOLTAGE
DSP POWER SUPPLY CONTROLLER WITH SEQUENCING
SLVS289A MARCH 2000 REVISED OCTOBER 2000
13
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
detailed description (continued)
deadtime control
Deadtime control prevents shoot-through current from flowing through the main power FETs during switching
transitions by actively controlling the turnon time of the MOSFET drivers. The high-side driver is not allowed
to turn on until the gate drive voltage to the low-side FET is below 1 V, and the low-side driver is not allowed
to turn on until the voltage at the junction of the 2 FETs (Vphase) is below 2 V.
current sensing
Current sensing is achieved by sampling and holding the voltage across the high-side power FET while the
high-side FET is on. The sampling network consists of an internal 60-
switch and an external hold capacitor.
Internal logic controls the turnon and turnoff of the sample/hold switch such that the switch does not turn on until
the Vphase voltage transitions high, and the switch turns off when the input to the high-side driver goes low.
Thus sampling will occur only when the high-side FET is conducting current. The voltage on the IOUT pin equals
2 times the sensed high-side voltage.
droop compensation
The droop compensation network reduces the load transient overshoot / undershoot on VOUT, relative to VREF
(see the application information section of this document for more details). VOUT is programmed to a voltage
greater than VREF by an external resistor divider from VOUT to the VSENSE pin to reduce the undershoot on
VOUT during a low to high load transient. The overshoot during a high to low load transient is reduced by
subtracting the voltage that is on the DROOP pin from VREF. The voltage on the IOUT pin is divided down with
an external resistor divider, and connected to the DROOP pin.
inhibit
INHIBIT is a TTL-compatible comparator pin that is used to enable the controller. When INHIBIT is lower than
the threshold, the output drivers are low and the slow-start capacitor is discharged. When INHIBIT goes high
(above 2.1 V), the short across the slow-start capacitor is released and normal converter operation begins.
When another system logic supply is connected to the INHIBIT pin, this pin controls power sequencing by
locking out controller operation until the system logic supply exceeds the input threshold voltage of the inhibit
circuit; thus the +3.3-V supply and another system logic supply (either +5 V or +12 V) must be above UVLO
thresholds before the controller is allowed to start up. Toggling the INHIBIT pin from low to high or recycling VCC
clears the fault latch.
slow-start
The slow-start circuit controls the rate at which both VOUTRR and VOUTLDO power up (at the same time). A
capacitor is connected between the SLOWST and ANAGND pins and is charged by an internal current source.
The value of the current source is proportional to the reference voltage, so that the charging rate of CSLOWST
is proportional to the ripple regulator reference voltage. The slow-start charging current is determined by the
following equation:
I
SLOWSTART +
I
VREFB
5
Where IVREFB is the current flowing out of the VREFB pin. It is recommended that no additional loads be
connected to VREFB, other than the resistor divider for setting the hysteresis voltage. Thus these resistor values
will determine the slow-start charging current. The maximum current that can be sourced by the VREFB circuit
is 500
A. The equation for the slow-start time is:
T
SLOWSTART +
5
C
SLOWSTART
R
VREFB
Where RVREFB is the total external resistance from VREFB to ANAGND.
相關PDF資料
PDF描述
TPS56302PWPRG4 2 A DUAL SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO28
TPS59116RGET SWITCHING CONTROLLER, PQCC24
TPS60110PWPRG4 0.3 A SWITCHED CAPACITOR REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO20
TPS60110PWPR 0.3 A SWITCHED CAPACITOR REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO20
TPS60110PWP 0.3 A SWITCHED CAPACITOR REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO20
相關代理商/技術參數
參數描述
TPS56302PWPRG4 功能描述:DC/DC 開關控制器 Dual Output Low Input Vltg Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS563200DDCR 功能描述:Buck Switching Regulator IC Positive Adjustable 0.76V 1 Output 3A SOT-23-6 Thin, TSOT-23-6 制造商:texas instruments 系列:D-CAP2??，Eco-Mode?? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:17V 電壓 - 輸出（最小值/固定）:0.76V 電壓 - 輸出（最大值）:7V 電流 - 輸出:3A 頻率 - 開關:650kHz 同步整流器:是 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商器件封裝:SOT-6 標準包裝:1
TPS563200DDCT 功能描述:Buck Switching Regulator IC Positive Adjustable 0.76V 1 Output 3A SOT-23-6 Thin, TSOT-23-6 制造商:texas instruments 系列:D-CAP2??，Eco-Mode?? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:17V 電壓 - 輸出（最小值/固定）:0.76V 電壓 - 輸出（最大值）:7V 電流 - 輸出:3A 頻率 - 開關:650kHz 同步整流器:是 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商器件封裝:6-SOT 標準包裝:1
TPS563200EVM-652 功能描述:EVAL BOARD FOR TPS563200 制造商:texas instruments 系列:D-CAP2?，Eco-Mode?，SWIFT? 零件狀態:在售 主要用途:DC/DC，步降 輸出和類型:1，非隔離 電壓 - 輸出:1.05V 電流 - 輸出:3A 電壓 - 輸入:4.5 V ~ 17 V 穩壓器拓撲:降壓 頻率 - 開關:650kHz 板類型:完全填充 所含物品:板 使用的 IC/零件:TPS563200 標準包裝:1
TPS563201DDCR 功能描述:IC REG BUCK ADJ 3A SYNC 制造商:texas instruments 系列:D-CAP2??，Eco-Mode?? 包裝:剪切帶（CT） 零件狀態:在售 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:17V 電壓 - 輸出（最小值/固定）:0.768V 電壓 - 輸出（最大值）:7V 電流 - 輸出:3A 頻率 - 開關:580kHz 同步整流器:是 工作溫度:-40°C ~ 125°C （TJ） 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商器件封裝:SOT-23-6 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*