參數資料
型號： TPS54354PWPG4
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： 6.5 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO16
封裝： GREEN, PLASTIC, HTSSOP-16
文件頁數： 8/35頁
文件大小： 858K
代理商： TPS54354PWPG4
TPS54352,TPS54353
TPS54354,TPS54355
TPS54356,TPS54357
SLVS519A MAY 2004 REVISED OCTOBER 2004
www.ti.com
16
LAYOUT INFORMATION
Figure 23. TPS5435x PCB Layout
PCB LAYOUT
The VIN pins should be connected together on the printed
circuit board (PCB) and bypassed with a low ESR ceramic
bypass capacitor. Care should be taken to minimize the
loop area formed by the bypass capacitor connections, the
VIN pins, and the TPS5435x ground pins. The minimum
recommended bypass capacitance is 10-
F ceramic with
a X5R or X7R dielectric and the optimum placement is
closest to the VIN pins and the AGND and PGND pins. See
Figure 23 for an example of a board layout. The AGND and
PGND pins should be tied to the PCB ground plane at the
pins of the IC. The source of the low-side MOSFET and the
anode of the Schottky diode should be connected directly
to the PCB ground plane. The PH pins should be tied
together and routed to the drain of the low-side MOSFET
or to the cathode of the external Schottky diode. Since the
PH connection is the switching node, the MOSFET (or
diode) should be located very close to the PH pins, and the
area of the PCB conductor minimized to prevent excessive
capacitive coupling. The recommended conductor width
from pins 14 and 15 is 0.050 inch to 0.075 inch of 1-ounce
copper. The length of the copper land pattern should be no
more than 0.2 inch.
For operation at full rated load, the analog ground plane
must provide adequate heat dissipating area. A 3-inch by
3-inch plane of copper is recommended, though not
mandatory, dependent on ambient temperature and
airflow. Most applications have larger areas of internal
ground plane available, and the PowerPAD should be
connected to the largest area available. Additional areas
on the bottom or top layers also help dissipate heat, and
any area available should be used when 3 A or greater
operation is desired. Connection from the exposed area of
the PowerPAD to the analog ground plane layer should be
made using 0.013-inch diameter vias to avoid solder
wicking through the vias. Four vias should be in the
PowerPAD area with four additional vias outside the pad
area and underneath the package. Additional vias beyond
those recommended to enhance thermal performance
should be included in areas not under the device package.
相關PDF資料
PDF描述
TPS54352PWPG4 6.5 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO16
TPS54356MPWPREP 6.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO16
TPS54357MPWPREP 6.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO16
TPS54354MPWPREP 6.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO16
TPS54362QPWPRQ1 8 A SWITCHING REGULATOR, 2200 kHz SWITCHING FREQ-MAX, PDSO20
相關代理商/技術參數
參數描述
TPS54354PWPR 功能描述:開關變換器、穩壓器與控制器 4.5 to 20V Inp 3-A Synch PWM Switch RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
TPS54354PWPRG4 功能描述:開關變換器、穩壓器與控制器 4.5 to 20V Inp 3-A Synch PWM Switch RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
TPS54355 制造商:TI 制造商全稱:Texas Instruments 功能描述:4.5V TO 20 V INPUT 3-A OUTPUT SYNCHRONOUS PWM SWITCHER WITH INTEGRATED FET
TPS54355-EP 制造商:TI 制造商全稱:Texas Instruments 功能描述:4.5-V TO 20-V INPUT, 3-A OUTPUT SYNCHRONOUS PWM SWITCHES
TPS54355MPWPREP 制造商:TI 制造商全稱:Texas Instruments 功能描述:4.5-V TO 20-V INPUT, 3-A OUTPUT SYNCHRONOUS PWM SWITCHES
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*