參數資料
型號： TPS54286PWPRG4
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： 3.6 A DUAL SWITCHING CONTROLLER, 750 kHz SWITCHING FREQ-MAX, PDSO14
封裝： GREEN, PLASTIC, HTSSOP-14
文件頁數： 5/52頁
文件大?。?/td> 1110K
代理商： TPS54286PWPRG4
www.ti.com
DELAY
IN
ENx
TH
ENx
t
C
farads
V
2 I
R
n
V
I
R
=
-
÷
-
è
l
(1)
TPS5428x
ENx
C
R
+
PVDD2
PVDDx
6 mA
1.2V
T
Time
-
t
DELAY
0
t
DELAY
+t
SS
PVDDx
ENx
V
OUTx
1.2-V
Threshold
SLUS749C – JULY 2007 – REVISED OCTOBER 2007
An R-C connected to an ENx pin may be used to delay the turn-on of the associated output after power is
applied to PVDDx (see Figure 15). After power is applied to PVDD2, the voltage on the ENx pin slowly decays
towards ground. Once the voltage decays to approximately 1.2 V, then the output is enabled and the startup
sequence begins. If it is desired to enable the outputs of the device immediately upon the application of power to
PVDD2, then omit these two components and tie the ENx pin to GND directly.
If an R-C circuit is used to delay the turn-on of the output, the resistor value must be much less than 1.2 V / 6
A
or 200 k
. A suggested value is 51 k. This resistor value allows the ENx voltage to decay below the 1.2-V
threshold while the 6-
A bias current flows.
The capacitor value required to delay the startup time (after the application of PVDD2) is shown in Equation 1.
where:
R and C are the timing components
V
TH is the 1.2-V enable threshold voltage
I
ENx is the 6A enable pin biasing current
Other enable pin functionality is dictated by the state of the SEQ pin. (See the Output Voltage Sequencing
section.)
Figure 15. Startup Delay Schematic
Figure 16. Startup Delay with R-C on Enable
DESIGN HINT
If delayed output voltage startup is not necessary, simply connect EN1 and EN2 to
GND. This configuration allows the outputs to start immediately on valid application of
PVDD2.
If ENx is allowed to go high after the Outputx has been in regulation, the upper MOSFET shuts off, and the
output decays at a rate determined by the output capacitor and the load. The internal pulldown MOSFET remains
in the OFF state. (See the Bootstrap for N-Channel MOSFET section.)
Copyright 2007, Texas Instruments Incorporated
13
Product Folder Link(s): TPS54283 TPS54286
相關PDF資料
PDF描述
TPS54290PWP 4.6 A DUAL SWITCHING CONTROLLER, 360 kHz SWITCHING FREQ-MAX, PDSO16
TPS54291PWPR 4.6 A DUAL SWITCHING CONTROLLER, 720 kHz SWITCHING FREQ-MAX, PDSO16
TPS5430DDAR 6 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8
TPS5430DDAG4 6 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8
TPS5430DDA 6 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
TPS54290 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.5-A/2.5-A Dual, Fully-Synchronous Buck Converter With Integrated MOSFET
TPS54290_1 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.5-A/2.5-A Dual, Fully-Synchronous Buck Converter With Integrated MOSFET
TPS54290_12 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.5-A/2.5-A Dual, Fully-Synchronous Buck Converter With Integrated MOSFET
TPS54290PWP 功能描述:直流/直流開關調節器 4.5-18V Dual Sync Step Down Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS54290PWPR 功能描述:直流/直流開關調節器 4.5-18V Dual Sync Step Down Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*