參數資料
型號： TPS54232D
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PDSO8
封裝： GREEN, PLASTIC, MS-012AA, SOIC-8
文件頁數： 9/24頁
文件大?。?/td> 601K
代理商： TPS54232D
BOOT
VSENSE
PH
VIN
GND
EN
Vout
PH
Vin
TOPSIDE
GROUND
AREA
OUTPUT
INDUCTOR
OUTPUT
FILTER
CAPACITOR
BOOT
CAPACITOR
INPUT
BYPASS
CAPACITOR
CATCH
DIODE
SignalVIA
RouteBOOT CAPACITOR
traceonotherlayertoprovide
widepathfortopsideground
RESISTOR
DIVIDER
Feedback Trace
COMP
SS
COMPENSATION
NETWORK
ThermalVIA
SLOWSTART
CAPACITOR
UVLO
RESISTOR
DIVIDER
SLVS876B
– NOVEMBER 2008 – REVISED FEBRUARY 2011
Ptot is the total device power dissipation (W).
TA is the ambient temperature (°C).
TJ is the junction temperature (°C) .
Rth is the thermal resistance of the package (
°C/W).
TJMAX is maximum junction temperature (°C).
TAMAX is maximum ambient temperature (°C).
PCB LAYOUT
The VIN pin should be bypassed to ground with a low ESR ceramic bypass capacitor. Care should be taken to
minimize the loop area formed by the bypass capacitor connections, the VIN pin, and the anode of the catch
diode. The typical recommended bypass capacitance is 10-
μF ceramic with a X5R or X7R dielectric and the
optimum placement is closest to the VIN pins and the source of the anode of the catch diode. See Figure 14 for
a PCB layout example. The GND D pin should be tied to the PCB ground plane at the pin of the IC. The source
of the low-side MOSFET should be connected directly to the top side PCB ground area used to tie together the
ground sides of the input and output capacitors as well as the anode of the catch diode. The PH pin should be
routed to the cathode of the catch diode and to the output inductor. Since the PH connection is the switching
node, the catch diode and output inductor should be located very close to the PH pins, and the area of the PCB
conductor minimized to prevent excessive capacitive coupling. For operation at full rated load, the top side
ground area must provide adequate heat dissipating area. The TPS54232 uses a fused lead frame so that the
GND pin acts as a conductive path for heat dissipation from the die. Many applications have larger areas of
internal or back side ground plane available, and the top side ground area can be connected to these areas
using multiple vias under or adjacent to the device to help dissipate heat. The additional external components
can be placed approximately as shown. It may be possible to obtain acceptable performance with alternate
layout schemes, however this layout has been shown to produce good results and is intended as a guideline.
Figure 14. TPS54232 Board Layout
2008–2011, Texas Instruments Incorporated
17
Product Folder Link(s): TPS54232
相關PDF資料
PDF描述
TPS54240DGQ SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10
TPS54262QPWPRQ1 SWITCHING REGULATOR, PDSO20
TPS54286PWPG4 3.6 A DUAL SWITCHING CONTROLLER, 750 kHz SWITCHING FREQ-MAX, PDSO14
TPS54283PWPR 3.6 A DUAL SWITCHING CONTROLLER, 375 kHz SWITCHING FREQ-MAX, PDSO14
TPS54286PWPRG4 3.6 A DUAL SWITCHING CONTROLLER, 750 kHz SWITCHING FREQ-MAX, PDSO14
相關代理商/技術參數
參數描述
TPS54232D 制造商:Texas Instruments 功能描述:Switching Regulator IC 制造商:Texas Instruments 功能描述:IC, STEP-DOWN DC/DC CONVERTER, 8-SOIC
TPS54232DR 功能描述:直流/直流開關調節器 2A,28V,1MHz Step Down SWIFT DC/DC RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS54232EVM-415 功能描述:電源管理IC開發工具 SWIFT Converter Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS54233 制造商:TI 制造商全稱:Texas Instruments 功能描述:2A, 28V INPUT, STEP DOWN SWIFT? DC/DC CONVERTER WITH ECO-MODE?
TPS54233D 功能描述:直流/直流開關調節器 28V,2A,300khZ Non- synch Buck RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*