- 您現在的位置：買賣IC網 > PDF目錄69510 > TPS54162QPWPRQ1 (TEXAS INSTRUMENTS INC) 3 A SWITCHING REGULATOR, 2200 kHz SWITCHING FREQ-MAX, PDSO20 PDF資料下載
參數資料
| 型號： | TPS54162QPWPRQ1 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 3 A SWITCHING REGULATOR, 2200 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | GREEN, PLASTIC, HTSSOP-20 |
| 文件頁數： | 3/41頁 |
| 文件大?。?/td> | 2414K |
| 代理商： | TPS54162QPWPRQ1 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
www.ti.com
SLVSA32C – OCTOBER 2009 – REVISED MAY 2010
OVERVIEW
The TPS54162 is a 60 V, 1 A DC/DC step down (buck) converter using voltage-control mode scheme. The
device features supervisory function for power-on-reset during system power on. Once the output voltage has
exceeded the threshold set by RST_TH pin, a delay of 1 ms/nF (based on capacitor value on Cdly terminal) is
invoked before the RST line is released high. Conversely on power down, once the output voltage falls below the
same set threshold, the RST line is pulled low only after a de-glitch filter of approximately 20 s (typical) expires.
This is implemented to prevent reset from being triggered due to fast transient line noise on the regulated output
supply.
An overvoltage monitor function, is used to limit regulated output voltage to the threshold set by OV_TH pin. Both
the RST_TH and OV_TH monitoring voltages are set to be a pre-scale of the output voltage, and thresholds
based on the internal bias voltages of the voltage comparators (0.8 V typical).
Detection of undervoltage on the regulated output is based on the RST_TH setting and will invoke RST line to be
asserted low. Detection of overvoltage on the output is based on the OV_TH setting and will not invoke the RST
line to be asserted low. However, the internal switch is commanded to turn OFF.
In systems where power consumption is critical, low-power mode (LPM) is implemented to reduce the
non-switching quiescent current during light load conditions. After the device has been operating in discontinuous
conduction mode (DCM) for at least 100 s (typ), depending upon the load current, it may enter in pulse skip
mode (PSM). The operation of when the device enters DCM is dependent on the selection of the external
components.
If thermal shutdown is invoked due to excessive power dissipation, the internal switch is disabled and the
regulated output voltage starts to decrease. Depending on the load current, the regulated output voltage could
decay and the RST_TH threshold may assert the RST output low.
DETAILED DESCRIPTION
The TPS54162 is a DC/DC converter using a voltage-control mode scheme with an input voltage feed-forward
technique. The device can be programmed for a range of output voltages with a wide input voltage range. Below
are details with regard to setting up the device, detailed functionality and the modes of operation.
Unregulated Input Voltage
The input voltage is supplied through VIN pins (pin 18 and 19) which must be externally protected against
voltage levels greater than 60 V and reverse input polarity. An external diode is connected to protect these pins
from reverse input polarity. The input current drawn from this pin is pulsed, with fast rise and fall times.
Therefore, this input line requires a filter capacitor to minimize noise. Additionally, for EMI considerations, an
input filter inductor may also be required.
NOTE
For design considerations, VIN/VReg ratios should always be set such that the minimum
required duty cycle pulse (tON-Min) is greater than 150 ns. The minimum off time (tOFF-Min) is
250 ns for all conditions.
Regulated Output Voltage
The regulated output voltage (VReg) is fed back to the device through VReg pin (pin 16). Typically, an output
capacitor of value within range of 10 F to 400 F is connected at this pin. It is also recommended to use a filter
capacitor with low ESR characteristics to minimize ripple in regulated output voltage. The VReg pin is also
internally connected to a load of ~100
, which is turned ON in the following conditions:
During startup condition, when the device is powered up with no-load, or whenever EN is toggled, the internal
load connected to VReg pin is turned ON to charge the bootstrap capacitor to provide gate drive voltage to
the switching transistor.
During normal operating conditions, when the regulated output voltage (VReg) exceeds the overvoltage
threshold (VReg_OV, preset by external resistors R1, R2, and R3), the internal load is turned ON, and this
pin is pulled down to bring the regulated output voltage down.
Copyright 2009–2010, Texas Instruments Incorporated
11
Product Folder Link(s): TPS54162-Q1
相關PDF資料 |
PDF描述 |
|---|---|
| TPS5420DR | 5 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS5420D | 6.5 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS54226PWP | DUAL SWITCHING CONTROLLER, PDSO20 |
| TPS54226RGTT | DUAL SWITCHING CONTROLLER, PQCC16 |
| TPS54232DR | SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS5420 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SWIFT Converter Product Portfolio |
| TPS54200DDCR | 功能描述:TPS54200DDCR 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1 |
| TPS54200DDCT | 功能描述:IC REG BUCK 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:在售 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:28V 電壓 - 輸出（最小值/固定）:-0.1V 電壓 - 輸出（最大值）:28V 電流 - 輸出:1.5A 頻率 - 開關:600kHz 同步整流器:是 工作溫度:-40°C ~ 125°C （TJ） 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商器件封裝:TSOT-23-6 標準包裝:1 |
| TPS54200EVM-818 | 功能描述:EVALUATION MODULE 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1 |
| TPS54201DDCR | 功能描述:TPS54201DDCR 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。