參數資料
型號： TPS40051QPWPRQ1
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
封裝： PLASTIC, HTSSOP-16
文件頁數： 5/35頁
文件大?。?/td> 498K
代理商： TPS40051QPWPRQ1
TPS40050Q1
TPS40051Q1
TPS40053Q1
SGLS219A NOVEMBER 2003 REVISED MAY 2008
www.ti.com
13
APPLICATION INFORMATION
SELECTING THE INDUCTOR VALUE
The inductor value determines the magnitude of ripple current in the output capacitors as well as the load current
at which the converter enters discontinuous mode. Too large an inductance results in lower ripple current but
is physically larger for the same load current. Too small an inductance results in larger ripple currents and a
greater number of (or more expensive output capacitors for) the same output ripple voltage requirement. A good
compromise is to select the inductance value such that the converter doesn’t enter discontinuous mode until
the load approximated somewhere between 10% and 30% of the rated output. The inductance value is
described in equation (6).
L
+
V
IN * VO
V
O
V
IN
DI
f
SW
(Henries)
where:.
D VO is the output voltage
D I is the peak-to-peak inductor current
CALCULATING THE OUTPUT CAPACITANCE
The output capacitance depends on the output ripple voltage requirement, output ripple current, as well as any
output voltage deviation requirement during a load transient.
The output ripple voltage is a function of both the output capacitance and capacitor ESR. The worst case output
ripple is described in equation (7).
DV + DI ESR )
1
8
C
O
f
SW
V
P
*P
The output ripple voltage is typically between 90% and 95% due to the ESR component.
The output capacitance requirement typically increases in the presence of a load transient requirement. During
a step load, the output capacitance must provide energy to the load (light to heavy load step) or absorb excess
inductor energy (heavy to light load step) while maintaining the output voltage within acceptable limits. The
amount of capacitance depends on the magnitude of the load step, the speed of the loop and the size of the
inductor.
Stepping the load from a heavy load to a light load results in an output overshoot. Excess energy stored in the
inductor must be absorbed by the output capacitance. The energy stored in the inductor is described in
equation (8).
E
L +
1
2
L
I2 (Joules)
where:
I2
+ I
OH
2
* I
OL
2
(Amperes)
2
where:
D IOH is the output current under heavy load conditions
D IOL is the output current under light load conditions
(6)
(7)
(8)
(9)
相關PDF資料
PDF描述
TPS40051PWP 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40050PWP 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40050PWPG4 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40051PWPR 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40053PWPG4 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
相關代理商/技術參數
參數描述
TPS40052 制造商:TI 制造商全稱:Texas Instruments 功能描述:WIDE INPUT SYNCHRONOUS BUCK CONTROLLER
TPS40052PWP 功能描述:DC/DC 開關控制器 Wide Input Sync Buck Cntrlr w/DDR trking RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40052PWPG4 功能描述:DC/DC 開關控制器 Wide Input Sync Buck Cntrlr w/DDR trking RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40052PWPR 功能描述:DC/DC 開關控制器 Wide Input Sync Buck Cntrlr w/DDR trking RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40052PWPRG4 功能描述:DC/DC 開關控制器 Wide Input Sync Buck Cntrlr w/DDR trking RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*