- 您現在的位置：買賣IC網 > PDF目錄69508 > TPS40040DRBRG4 (TEXAS INSTRUMENTS INC) 7.2 A SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | TPS40040DRBRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 7.2 A SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 3 X 3 MM, PLASTIC, SON-8 |
| 文件頁數： | 5/38頁 |
| 文件大?。?/td> | 741K |
| 代理商： | TPS40040DRBRG4 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
www.ti.com
Output Short Circuit Protection
Selecting the Short Circuit Current Limit Threshold
Synchronous Rectification and Gate Drive
SLUS700D – MARCH 2006 – REVISED DECEMBER 2007
To minimize circuit losses, the TPS40040/1 uses the RDS(on) of the upper MOSFET switch as the current sensing
element. The current limit comparator, initially blanked during the first portion of each switching cycle, senses the
voltage across the high-side MOSFET when it is fully ON. This voltage is compared to an internally selected
short circuit current (SCC) limit threshold voltage. If the comparator senses a voltage drop across the high-side
MOSFET greater than the SCC limit threshold, it outputs an OC pulse. This terminates the current PWM pulse
preventing further current ramp-up, and sets the fault counter to count up one count on the next clock cycle.
Similarly, if no OC pulse is detected, the fault counter decrements by one count. If seven OC pulses are
summed, a fault condition is declared and the upper switch of the PWM output of the chip is immediately
disabled (turned OFF) and remains that way until the fault time-out period has elapsed. Both HDRV and LDRV
drivers are kept OFF during the fault time-out.
The fault time-out period is determined by cycling through seven internal soft-start time periods. At the end of the
fault time-out period, startup is attempted again.
The main purpose is for hard fault protection of the power switches. The internal SCC voltage has a positive
temperature coefficient designed to improve the short circuit threshold tolerance variation with temperature.
However, given the tolerance of the voltage thresholds and the RDS(on) range for a MOSFET, it is possible to
apply a load that thermally damages the external MOSFETs.
The TPS40040/1 uses one of three user selectable voltage thresholds. During the calibration interval at power on
or enable (Figure 19), the TPS40040/1 monitors the current out of the COMP pin and selects a threshold based
on the sensed value. If the current is zero; that is, no resistor is connected between COMP and GND, then the
threshold voltage level is 180 mV. If a 2.4-k
resistor is connected between COMP and GND, then the threshold
voltage level is 105 mV. If a 12-k
resistor is connected between COMP and GND, then the threshold voltage is
310 mV.
Once calibration is complete, the selected SCP threshold level is latched into place and remains constant. In
addition, the sensing circuits on COMP pin during calibration are disconnected from the COMP pin, and soft start
is allowed to begin.
In a buck converter, when the upper switch MOSFET turns off, current is flowing in the inductor to the load. This
current cannot be stopped immediately without using infinite voltage. To give this current a path to flow and
maintain voltage levels at a safe level, a rectifier or catch device is used. This device can be either a diode, or it
can be a controlled active device. The TPS40040/1 provides a signal to drive an N-channel MOSFET as a
synchronous rectifier (SR). This control signal is carefully coordinated with the drive signal for the main switch so
that there is minimum dead time from the time that the SR turns OFF and the upper switch MOSFET turns ON,
and minimum delay from when the upper switch MOSFET turns OFF and the SR turns ON.
NOTE:
The longer the time spent in diode conduction during the rectifier conduction period,
the lower the converter efficiency.
The drivers for the external HDRV and LDRV MOSFETs are capable of driving a gate to source voltage of
approximately 5 V. At VDD = 5 V, the drivers are capable of driving MOSFETs appropriate for a 15-A converter.
The LDRV driver switches between VDD and ground, while HDRV driver is referenced to SW and switches
between BOOT and SW. The drivers have non-overlapping timing that is governed by an adaptive delay circuit
that minimizes body diode conduction in the synchronous rectifier.
Copyright 2006–2007, Texas Instruments Incorporated
13
相關PDF資料 |
PDF描述 |
|---|---|
| TPS40040DRBT | 7.2 A SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS40041DRBRG4 | 7.2 A SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS40050QPWPRQ1 | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40051QPWPRQ1 | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40051PWP | 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS40040DRBT | 功能描述:DC/DC 開關控制器 Low Vin Synch Buck DC/DC Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40040DRBT | 制造商:Texas Instruments 功能描述:Peak Reflow Compatible (260 C):Yes |
| TPS40040DRBTG4 | 功能描述:DC/DC 開關控制器 Lo Vin Synch Buck DC/DC Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40040EVM-001 | 功能描述:電源管理IC開發工具 10A Synch Buck Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS40041 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW PIN COUNT, LOW VIN (2.5 V TO 5.5 V) SYNCHRONOUS BUCK DC-TO-DC CONTROLLER WITH ENABLE |
發布緊急采購，3分鐘左右您將得到回復。