參數資料
型號: TPS3620-50DGKTG4
廠商: TEXAS INSTRUMENTS INC
元件分類: 電源管理
英文描述: 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
封裝: 3.05 X 4.98 MM, GREEN, PLASTIC, MSOP-8
文件頁數: 2/17頁
文件大?。?/td> 494K
代理商: TPS3620-50DGKTG4
www.ti.com
DETAILED DESCRIPTION
Battery Freshness Seal (TPS3619)
Power-Fail Comparator (PFI and PFO)
Backup-Battery Switchover
SLVS387H – APRIL 2001 – REVISED DECEMBER 2007
The battery freshness seal of the TPS3619 family disconnects the backup-battery from internal circuitry until it is
needed. This function prevents the backup-battery from being discharged unitl the final product is put to use. The
following steps explain how to enable the freshness seal mode.
1. Connect VBAT (VBAT > VBAT min)
2. Ground PFO
3. Connect PFI to VDD (PFI = VDD)
4. Connect VDD to power supply (VDD > VIT) and keep connected for 5 ms < t < 35 ms
The battery freshness seal mode is automatically removed by the positive-going edge of RESET when VDD is
applied.
An additional comparator is provided to monitor voltages other than the nominal supply voltage. The
power-fail-input (PFI) is compared with an internal voltage reference of 1.15 V. If the input voltage falls below the
power-fail threshold VIT(PFI) of typical 1.15 V, the power-fail output (PFO) goes low. If VIT(PFI) goes above V(PFI),
plus about 12-mV hysteresis, the output returns to high. By connecting two external resistors, it is possible to
supervise any voltages above V(PFI). The sum of both resistors should be about 1 M, to minimize power
consumption and also to assure that the current in the PFI pin can be ignored compared with the current through
the resistor network. The tolerance of the external resistors should be not more than 1% to ensure minimal
variation of sensed voltage. If the power-fail comparator is unused, PFI should be connected to ground and PFO
left unconnected.
In case of a brownout or power failure, it may be necessary to preserve the contents of RAM. If a backup battery
is installed at VBAT, the device automatically switches the connected RAM to backup power when VDD fails. In
order to allow the backup battery (e.g., a 3.6-V lithium cell) to have a higher voltage than VDD, these supervisors
do not connect VBAT to VOUT when VBAT is greater than VDD. VBAT only connects to VOUT (through a 15- switch)
when VDD falls below VIT and VBAT is greater than VDD. When VDD recovers, switchover is deferred either until
VDD crosses VBAT, or until VDD rises above the reset threshold VIT. VOUT connects to VDD through a 1- (max)
PMOS switch when VDD crosses the reset threshold.
FUNCTION TABLE
VDD > VBAT
VDD > VIT
VOUT
1
VDD
1
0
VDD
0
1
VDD
0
VBAT
10
Copyright 2001–2007, Texas Instruments Incorporated
相關PDF資料
PDF描述
TPS3620-50DGKT 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
TPS3705-50DGNG4 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
TPS3705-50DG4 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
TPS3705-50DGNR 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
TPS3705-30D 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
相關代理商/技術參數
參數描述
TPS3700 制造商:TI 制造商全稱:Texas Instruments 功能描述:Window Comparator for Over- and Undervoltage Detection
TPS3700DDCR 功能描述:監控電路 Window Comp for Over & Under Vltg Det RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
TPS3700DDCR2 制造商:Texas Instruments 功能描述:IC COMPARATOR WINDOW 6SOT 制造商:Texas Instruments 功能描述:High voltage supervisor
TPS3700DDCT 功能描述:監控電路 Window Comp for Over & Under Vltg Det RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
TPS3700DSER 功能描述:Comparator Window Open Drain 6-WSON (1.5x1.5) 制造商:texas instruments 系列:- 包裝:剪切帶(CT) 零件狀態:有效 類型:窗口 元件數:1 輸出類型:開路漏極 電壓 - 電源,單/雙(±):1.8 V ~ 18 V 電壓 - 輸入失調(最大值):- 電流 - 輸入偏置(最大值):- 電流 - 輸出(典型值):- 電流 - 靜態(最大值):13μA CMRR,PSRR(典型值):- 傳播延遲(最大值):29μs 滯后:5.5mV 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WFDFN 安裝類型:表面貼裝 供應商器件封裝:6-WSON(1.5x1.5) 標準包裝:1