- 您現在的位置：買賣IC網 > PDF目錄69504 > TPS2420RSAR (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 PDF資料下載
參數資料
| 型號： | TPS2420RSAR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| 封裝： | 4 X 4 MM, PLASTIC, QFN-16 |
| 文件頁數： | 7/29頁 |
| 文件大?。?/td> | 1368K |
| 代理商： | TPS2420RSAR |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
www.ti.com
SLUS903C – JANUARY 2009 – REVISED AUGUST 2010
APPLICATION INFORMATION
Operation
When load current exceeds the user programmed fault limit (IFAULT) during normal operation the fault timer starts.
If load current drops below the IFAULT threshold before the fault timer expires, normal operation continues. If load
current stays above the IFAULT threshold the fault timer expires and a fault is declared. When a fault is declared a
device operating in latch mode turns off and can be restarted by cycling power or toggling the EN signal. A
device operating in retry mode attempts to turn on at a 3% duty cycle until the fault is cleared. When the IMAX
limit is reached during a fault the device goes into current limit and the fault timer keeps running. IMAX can be
programmed by the user by connecting a resistor from the IMAX pin to GND.
Startup
When power is first applied to a load with discharged capacitors there is a large inrush current. The inrush is
controlled by the TPS2420 by initially entering the power limit mode and turning on the fault timer. See Figure 19.
As the charge builds on the capacitor, the current increases to IMAX. When the capacitor is fully charged, current
output is set by the dc load value, The fault timer is turned off. The FET is then fully enhanced and the power
good signal is true.
In order to start properly, the fault timer must be set to exceed the capacitor charge time.
When the load has a resistive component as well as capacitive, the fault time needs to be increased because
current to the resistive load is unavailable to charge the capacitor. The startup time for some selected loading is
given in Table 1.
Table 1 data was taken with IFAULT set to 4 A and IILIM set to 5 A. Lower current settings of TPS2420 do not have
a great influence on the start up timer because of operation at power limit. Load capacitance and dc resistance
was selected for a measured start time. The start time is measured from the assertion of the EN pin to the
assertion of the PG pin.
Table 1. Start Time for Input Voltage and Output Loading(1)
LOAD CAPACITANCE
DC LOAD
INPUT VOLTAGE (V)
START TIME (ms)
(mF)
RESISTANCE (
)
OPEN
2.5
220
5
2.7
12
2.6
5
OPEN
4
1000
5
4
12
4
OPEN
4.4
220
5
No start
12
7
12
OPEN
14
1000
5
No start
12
23
(1)
IFAULT = 4 A, IILIM = 5 A.
Some combinations of loading and current limit settings exceed the 5-W power limit of the internal MOSFET. The
output voltage will not turn on regardless of the fault time setting. One way to work with the physical limits that
create this problem is to allow the power manager to charge only the capacitive component of the load and use
the PG signal to turn on the resistive component. This is common usage in dc-to-dc converters and other
electrical equipment with power good inputs.
Copyright 2009–2010, Texas Instruments Incorporated
15
Product Folder Link(s): TPS2420
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2458RHBT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| TPS2458RHBR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| TPS24720RGTT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| TPS24720RGTR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| TPS2500DRCT | 6 A SWITCHING REGULATOR, 1075 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2420RSAT | 功能描述:熱插拔功率分布 Int FET 0-5A Dual Fault Threshold RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2420RSAT | 制造商:Texas Instruments 功能描述:Hot Swap Contoller IC |
| TPS2421-1DDA | 功能描述:熱插拔功率分布 3-20V Integ FET 0-5A Hot Swap RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2421-1DDAR | 功能描述:熱插拔功率分布 3-20V Integ FET 0-5A Hot Swap RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2421-1EVM-02 | 功能描述:電源管理IC開發工具 TPS2421-1 Hot Swap Controller Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。