- 您現在的位置：買賣IC網 > PDF目錄69504 > TPS2412DG4 (TEXAS INSTRUMENTS INC) SPECIALTY ANALOG CIRCUIT, PDSO8 PDF資料下載
參數資料
| 型號： | TPS2412DG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| 封裝： | GREEN, PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 8/25頁 |
| 文件大小： | 1052K |
| 代理商： | TPS2412DG4 |
SUMMARIZED DESIGN PROCEDURE
Layout Considerations
SLVS728B – JANUARY 2007 – REVISED SEPTEMBER 2008.......................................................................................................................................... www.ti.com
The following is a summarized design procedure:
1. Choose between the TPS2412 or 2413, see TPS2412 vs TPS2413 – MOSFET Control Methods
2. Choose the VDD source. Table 3 provides a guide for where to connect VDD that covers most cases. VDD may
be directly connected to the supply, but an R(VDD) and C(VDD) of 10 and 0.01 F is recommended.
Table 3. VDD Connection Guide
VA < 3 V
3 V
≤ VA ≤ 3.6 V
VA > 3.6 V
Bias Supply > 3 V
VA or Bias Supply > 3 V. VC if always > 3 V
VC, VA, or Bias for special configurations
3. Noise voltage and impedance at the A pin should be kept low. C(A) may be required if there is noise on the
bus, or A is not low impedance. If either of these is a concern, a C(A) of 0.01 F or more may be required.
4. Select C(BYP) as 2200 pF, X7R, 25-V or 50-V ceramic capacitor.
5. Select the MOSFET based on considerations of voltage drop, power dissipated, voltage ratings, and gate
capacitance. See sections: MOSFET Selection and RSET and TPS2412 Regulation-Loop Stability.
6. Select R(RSET) based on which MOSFET was chosen and reverse current considerations – see MOSFET
Selection and RSET. If the noise and transient environment is not well known, make provision for R(RSET)
even when using the TPS2412.
7. Make sure to connect RSVD to ground
1. The TPS2412/13, MOSFET, and associated components should be used over a ground plane.
2. The GND connection should be short, with multiple vias to ground.
3. C(VDD) should be adjacent to the VDD pin with a minimal ground connection length to the plane.
4. The GATE connection should be short and wide (e.g., 0.025" minimum).
5. The C pin should be Kelvin connected to the MOSFET.
6. The A pin should be a short, wide, Kelvin connection to the MOSFET.
7. R(SET) should be kept immediately adjacent to the TPS2412/13 with short leads.
8. C(BYP) should be kept immediately adjacent to the TPS2412/13 with short leads.
16
Copyright 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2412 TPS2413
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2413D | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| TPS2413PWR | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| TPS2420RSAR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| TPS2458RHBT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| TPS2458RHBR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2412DR | 功能描述:熱插拔功率分布 N+1/ORing Power Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2412DRG4 | 功能描述:熱插拔功率分布 N+1/ORing Pwr Cntrlr RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2412EVM | 功能描述:電源管理IC開發工具 TPS2412 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS2412PW | 功能描述:熱插拔功率分布 N+1 OR-ing Pwr Rail Cntrlr RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2412PWG4 | 功能描述:熱插拔功率分布 N+1 and OR-ing Pwr Rail Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。