- 您現在的位置：買賣IC網 > PDF目錄69503 > TPS23770PWPG4 (TEXAS INSTRUMENTS INC) 1.3 A SWITCHING CONTROLLER, 565 kHz SWITCHING FREQ-MAX, PDSO20 PDF資料下載
參數資料
| 型號： | TPS23770PWPG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.3 A SWITCHING CONTROLLER, 565 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | GREEN, PLASTIC, HTSSOP-20 |
| 文件頁數： | 8/38頁 |
| 文件大小： | 1036K |
| 代理商： | TPS23770PWPG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
www.ti.com
PoE THRESHOLDS
V
UVLO_R
Detection
Classification
PD Powered
Idle
V
CL_ON
V
CL_H
1.4V
V
CU_OFF
V
CU_H
V
UVLO_F
V
DD
DETECTION
CLASSIFICATION
SLVS590B – JULY 2005 – REVISED FEBRUARY 2008
The TPS23750 has a number of internal comparators with hysteresis for stable switching between the various
states as shown in Figure 29. Figure 30 relates the parameters in the Electrical Characteristics section to the
PoE states. The mode labeled idle between classification and operation implies that the DET, CLASS, and RTN
pins are all high impedance.
Figure 30. Threshold Voltages
This feature of IEEE 802.3af reduces the risk of damaging Ethernet devices not intended for application of 48 V.
When a voltage in the range of 2.7 V to 10.1 V is applied to the PI, an incremental resistance of 25 k
signals
the PSE that the PD is both capable of, and ready to, accept power. The incremental resistance is measured by
applying at least two different voltages to the PI and measuring the current it draws. These two test voltages
must be within the specified range and be at least 1 V apart. The incremental resistance equals the difference
between the voltages divided by the difference between the currents. The allowed range of resistance is 23.75
k
to 26.25 k.
The TPS23750 is in detection mode whenever the supply voltage is below the lower classification threshold. The
TPS23750 draws a minimum of bias power in this condition, while RTN is high impedance and almost all the
internal circuits are disabled. The DET pin is pulled to ground during detection, so a 24.9 k
, 1% resistor from
VDD to DET presents the correct signature. RDET may be a small, low-power resistor since it only sees a stress of
about 5 mW. When the input voltage rises above the 11.3 V upper detection comparator threshold, the DET pin
goes to an open-drain condition to conserve power.
The input diode bridge’s incremental resistance may be hundreds of Ohms at the very low currents seen at 2.7 V
on the PI. The bridge’s resistance is in series with RDET and increases the total resistance seen by the PSE. The
nonlinearity in the detection signature of Figure 29 is caused by the diode bridge. This varies with the type of
diode selected by the designer, and it is not usually specified on the diode data sheet. The value of RDET may be
adjusted downwards to accommodate a particular diode type.
Once the PSE has detected a PD, it may optionally classify the PD. Classification allows a PSE to determine a
PD’s power requirements rather than assuming every PD requires 15.4 W, which allows the PSE to power the
maximum number of PDs from its 48-V power supply. This step is optional because some PSEs can afford to
allot the full power to every powered port.
The classification process applies a voltage between 14.5 V and 20.5 V to the input of the PD, which in turn
draws a fixed current set by RCLASS. The PSE measures the PD current to determine which of the five available
classes (see Table 2) that the PD falls into. The total current drawn from the PSE during classification is the sum
of bias currents and current through RCLASS. The TPS23750 disconnects RCLASS at voltages above the
classification range to avoid excessive power dissipation (see Figure 29 and Figure 30).
16
Copyright 2005–2008, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2377DR-1 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2375PWR-1G4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2377D-1 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2377DR-1G4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2375PW-1 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS23770PWPR | 功能描述:熱插拔功率分布 IEEE 802.3af PD Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS23770PWPRG4 | 功能描述:熱插拔功率分布 IEEE 802.3af PD Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2377D | 功能描述:熱插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2377D-1 | 功能描述:熱插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2377D-1G4 | 功能描述:熱插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。