參數資料
型號: TPS2370DRG4
廠商: TEXAS INSTRUMENTS INC
元件分類: 電源管理
英文描述: 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
封裝: GREEN, PLASTIC, MS-012AA, SOIC-8
文件頁數: 12/17頁
文件大小: 426K
代理商: TPS2370DRG4
TPS2370
SLUS537C AUGUST 2002 REVISED MARCH 2004
www.ti.com
4
TERMINAL FUNCTIONS
TERMINAL
I/O
DESCRIPTION
NAME
NO.
I/O
DESCRIPTION
CLASS
2
O
Sets classification level with a single resistor to VEE. A precision voltage of 10 V is applied to this pin during
classification. RCLASS values listed in Table 1.
DET
3
O
Connect the 24.9-k
detection resistor (RDET) between this pin and VDD.
EN_DC
6
O
Ties to dc-to-dc converter’s shutdown or soft-start pin. Sinks 80
A until the load capacitor is fully charged.
ILIM
1
O
Sets start-up current limit level with a resistor to VEE. If using CDC2DCIN > 180 F, IRUSH must be less than
400 mA. Extra capacitance on ILIM pin can cause oscillations in the current waveform.
RTN
5
O
Return pin. Connect this pin to input return side of the dc-to-dc converter.
VDD
8
I
Connection to PD input port positive voltage.
VEE
4
I
Input side power return for the controller.
(1) I
INRUSH + 450 mA *
25 k
W
R
LIM
(1A)
DETAILED PIN DESCRIPTIONS
ILIM (Pin 1)
Inrush current limiting pin. This pin is used to program the inrush current of the device. By placing a resistor to VEE
from this pin, the inrush current into the load is limited via the following equation:
I
INRUSH + 450 mA *
25 k
W
R
LIM
(1A)
CLASS (Pin 2)
Classification pin. The PD can be optionally classified by adding a resistor from this pin to ground. The resistor specific
to each class is given in Table 1: PoE Classification Resistance Values.
DET (Pin3)
Detection pin. This pin is used to set up the detection resistance during PD detection. By tying a resistor, RDET, from
this pin to VDD, the user sets the detection resistance. It should be noted that the device itself looks like approximately
1 M
of resistance in parallel with RDET.
VEE (Pin 4)
Negative supply to the device.
RET (Pin 5)
Negative supply to the load. This pin is the drain side of a FET between the RET pin and the VEE pin, providing hot
swap capabilities to the load. When the FET is switched on, there is approximately 300 m
between this pin and VEE.
EN_DC (Pin 6)
Enable pin for the load. This pin is intended to be used with a dc-to-dc coverter with a soft start capacitor. When power
is not available to the dc-to-dc converter, this pin sinks 80
A and holds off the soft-start capacitor on the dc-to-dc
converter. Once the voltage across the load is within 1.5 V of its final value, the EN_DC pin stops drawing current
and becomes high impedance, allowing the dc-to-dc converter to soft start normally.
VDD (Pin 8)
Positive supply to the device.
(1)
相關PDF資料
PDF描述
TC151A3113EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151A2620EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151B3622EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151A3135EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151B5148EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
TPS2370EVM 制造商:Texas Instruments 功能描述:TPS2370EVM - Bulk
TPS2370PW 功能描述:熱插拔功率分布 IEEE 802.3af Pwr Ifc Switch For PoE PD’s RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2370PWG4 功能描述:熱插拔功率分布 IEEE 802.3af Pwr Ifc Switch For PoE PD’s RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2370PWR 功能描述:熱插拔功率分布 IEEE 802.3af Pwr Ifc Switch For PoE PD’s RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2370PWRG4 功能描述:熱插拔功率分布 IEEE 802.3af Pwr Ifc Switch For PoE PD’s RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube