- 您現在的位置：買賣IC網 > PDF目錄385945 > TPS2330D (Texas Instruments, Inc.) SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING PDF資料下載
參數資料
| 型號： | TPS2330D |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING |
| 中文描述： | 單熱插拔功率斷路器及功率控制器，高質量的報告 |
| 文件頁數： | 13/20頁 |
| 文件大?。?/td> | 345K |
| 代理商： | TPS2330D |
TPS2330, TPS2331
SINGLE HOT SWAP POWER CONTROLLER WITH
CIRCUIT BREAKER AND POWER-GOOD REPORTING
SLVS277A – MARCH 2000– REVISED APRIL 2000
13
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
typical application diagram
This diagram shows a typical dual hot-swap application. The pullup resistors at PWRGD and Fault should be
relatively large (e.g. 100 k
) to reduce power loss unless they are required to drive a large load.
VREG
0.1
μ
F
IN
ISET
RISET
ISENSE
RSENSE
GATE DISCH
VSENSE
RVSENSE_TOP
RVSENSE_BOTTOM
+
FAULT
PWRGD
FAULT
PWRGD
TIMER
ENABLE
DGND
AGND
VO
ENABLE
1
μ
F
～
10
μ
F
3 V
～
13 V IN
TPS2331
System
Board
Figure 18. Typical Hot-Swap Application
input capacitor
A 0.1-
μ
F ceramic capacitor in parallel with a 1-
μ
F ceramic capacitor should be placed on the input power
terminals near the connector on the hot-plug board to help stabilize the voltage rails on the cards. The
TPS2330/31 does not need to be mounted near the connector or these input capacitors. For applications with
more severe power environments, a 2.2-
μ
F or higher ceramic capacitor is recommended near the input
terminals of the hot-plug board. A bypass capacitor for IN should be placed close to the device.
output capacitor
A 0.1-
μ
F ceramic capacitor is recommended per load on the TPS2330/31; these capacitors should be placed
close to the external FETs and to TPS2330/31. A larger bulk capacitor on the load is also recommended. The
value of the bulk capacitor should be selected based on the power requirements and the transients generated
by the application.
external FET
To deliver power from the input sources to the loads, the controller needs an external N-channel MOSFET. A
few widely used MOSFETs are shown in Table 1. But many other MOSFETs on the market can also be used
with TPS23xx in hot-swap systems.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2330PW | SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING |
| TPS2331D | SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING |
| TPS2331PW | SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING |
| TPS2330EVM-184 | TPS2330 48-V Telecom Hot Swap Evaluation Module and Interface Card(48V遠程通信熱交換電源控制器TPS2330的評估板與接口卡) |
| TPS2330EVM-185 | TPS2330/TPS2331,TPS5102 InfiniBand SM Bulk Power Evalutation Module and Interface Card( InfiniBand SM 降壓電源管理器件TPS2330/TPS2331, TPS5102的評估板與接口卡) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2330EVM-184 | 功能描述:電源管理IC開發工具 TPS2330 48-V Telecom Hot Swap Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS2330EVM-185 | 功能描述:電源管理IC開發工具 Infiniband Bulk Pow Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS2330ID | 功能描述:熱插拔功率分布 3-13V Sngl w/Pwr Gd Rpt Act-Lo Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2330IDG4 | 功能描述:熱插拔功率分布 3-13V Sngl w/Pwr Gd Rpt Act-Lo Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2330IDR | 功能描述:熱插拔功率分布 3-13V Sngl w/Pwr Gd Rpt Act-Lo Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。