參數資料
型號: TPS2321PW
廠商: Texas Instruments, Inc.
英文描述: DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER
中文描述: 雙熱插拔電源控制器與廉政斷路器
文件頁數: 18/22頁
文件大?。?/td> 409K
代理商: TPS2321PW
TPS2320, TPS2321
DUAL HOT SWAP POWER CONTROLLER
WITH INDEPENDENT CIRCUIT BREAKER
SLVS276A – MARCH 200 – REVISED APRIL 2000
18
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
undervoltage lockout (UVLO)
The TPS2320/TPS2321 includes an undervoltage lockout (UVLO) feature that monitors the voltage present on
the VREG pin. This feature will disable both external MOSFETs if the voltage on VREG drops below 2.78 V
(nominal) and will re-enable normal operation when it rises above 2.85 V (nominal). Since VREG is fed from
IN1 through a low-dropout voltage regulator, the voltage on VREG will track the voltage on IN1 within 50 mV.
While the undervoltage lockout is engaged, both GATE1 and GATE2 are held low by internal PMOS pulldown
transistors, ensuring that the external MOSFET transistors remain off at all times, even if all power supplies have
fallen to 0 V.
single-channel operation
Some applications may require only a single external MOS transistor. Such applications should use GATE1 and
the associated circuitry (IN1, ISENSE1, ISET1, DISCH1). The IN2 pin should be grounded to disable the
circuitry associated with the GATE2 pin.
power-up control
The TPS2320/TPS2321 includes a 500
μ
s (nominal) startup delay that ensures that internal circuitry has
sufficient time to start before the device begins turning on the external MOSFETs. This delay is triggered only
upon the rapid application of power to the circuit. If the power supply ramps up slowly, the undervoltage lockout
circuitry will provide adequate protection against undervoltage operation.
3-channel hot-swap application
Some applications require hot-swap control of up to three voltage rails, but may not explicitly require the sensing
of the status of the output power on all three of the voltage rails. One such application is device bay, where dv/dt
control of 3.3 V, 5 V, and 12 V is required. By using Channel 2 to drive both the 3.3-V and 5-V power rails and
Channel 1 to drive the 12-V power rail, as is shown below, TPS2320/01 can deliver three different voltages to
three loads while monitoring the status of two of the loads.
相關PDF資料
PDF描述
TPS2330D SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING
TPS2330PW SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING
TPS2331D SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING
TPS2331PW SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING
TPS2330EVM-184 TPS2330 48-V Telecom Hot Swap Evaluation Module and Interface Card(48V遠程通信熱交換電源控制器TPS2330的評估板與接口卡)
相關代理商/技術參數
參數描述
TPS2330EVM-184 功能描述:電源管理IC開發工具 TPS2330 48-V Telecom Hot Swap Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS2330EVM-185 功能描述:電源管理IC開發工具 Infiniband Bulk Pow Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS2330ID 功能描述:熱插拔功率分布 3-13V Sngl w/Pwr Gd Rpt Act-Lo Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2330IDG4 功能描述:熱插拔功率分布 3-13V Sngl w/Pwr Gd Rpt Act-Lo Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2330IDR 功能描述:熱插拔功率分布 3-13V Sngl w/Pwr Gd Rpt Act-Lo Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube