參數資料
型號: TPS2320PW
廠商: Texas Instruments, Inc.
英文描述: DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER
中文描述: 雙熱插拔電源控制器與廉政斷路器
文件頁數: 18/22頁
文件大小: 409K
代理商: TPS2320PW
TPS2320, TPS2321
DUAL HOT SWAP POWER CONTROLLER
WITH INDEPENDENT CIRCUIT BREAKER
SLVS276A – MARCH 200 – REVISED APRIL 2000
18
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
undervoltage lockout (UVLO)
The TPS2320/TPS2321 includes an undervoltage lockout (UVLO) feature that monitors the voltage present on
the VREG pin. This feature will disable both external MOSFETs if the voltage on VREG drops below 2.78 V
(nominal) and will re-enable normal operation when it rises above 2.85 V (nominal). Since VREG is fed from
IN1 through a low-dropout voltage regulator, the voltage on VREG will track the voltage on IN1 within 50 mV.
While the undervoltage lockout is engaged, both GATE1 and GATE2 are held low by internal PMOS pulldown
transistors, ensuring that the external MOSFET transistors remain off at all times, even if all power supplies have
fallen to 0 V.
single-channel operation
Some applications may require only a single external MOS transistor. Such applications should use GATE1 and
the associated circuitry (IN1, ISENSE1, ISET1, DISCH1). The IN2 pin should be grounded to disable the
circuitry associated with the GATE2 pin.
power-up control
The TPS2320/TPS2321 includes a 500
μ
s (nominal) startup delay that ensures that internal circuitry has
sufficient time to start before the device begins turning on the external MOSFETs. This delay is triggered only
upon the rapid application of power to the circuit. If the power supply ramps up slowly, the undervoltage lockout
circuitry will provide adequate protection against undervoltage operation.
3-channel hot-swap application
Some applications require hot-swap control of up to three voltage rails, but may not explicitly require the sensing
of the status of the output power on all three of the voltage rails. One such application is device bay, where dv/dt
control of 3.3 V, 5 V, and 12 V is required. By using Channel 2 to drive both the 3.3-V and 5-V power rails and
Channel 1 to drive the 12-V power rail, as is shown below, TPS2320/01 can deliver three different voltages to
three loads while monitoring the status of two of the loads.
相關PDF資料
PDF描述
TPS2321D DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER
TPS2321PW DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER
TPS2330D SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING
TPS2330PW SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING
TPS2331D SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING
相關代理商/技術參數
參數描述
TPS2321ID 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2321IDG4 功能描述:熱插拔功率分布 3-13V Dual Hot- Swap IC RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2321IDR 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2321IDRG4 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2321IPW 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube