- 您現在的位置：買賣IC網 > PDF目錄98279 > TPS22934YZVR (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4 PDF資料下載
參數資料
| 型號： | TPS22934YZVR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4 |
| 封裝： | 0.90 X 0.90 MM, 0.50 MM PITCH, GREEN, DSBGA-4 |
| 文件頁數： | 13/25頁 |
| 文件大?。?/td> | 976K |
| 代理商： | TPS22934YZVR |
SLVSAD4 – AUGUST 2010
www.ti.com
APPLICATION INFORMATION
ON/OFF Control
The ON pin controls the state of the switch. The TPS22934 has built-in hysteresis on its control inputs. The load
switch is active when the ON voltage is greater than the positive going voltage threshold (VTH+). If the ON voltage
is lower than the negative going voltage threshold (VTH-), then the pass FET is deactivated and the active
pulldown from VOUT to GND is activated.
This is ideal for power rail sequencing applications as shown in Figure 2 where the 2.8-V supply needs to be
valid before the 1.8-V supply turn on:
Figure 2. 1.8-V / 2.8-V Power Rail Sequencing
Input Capacitor
To limit the voltage drop on the input supply caused by transient in-rush currents when the switch turns on into a
discharged load capacitor or short-circuit, a capacitor needs to be placed between VIN and GND. A 1-F ceramic
capacitor, CIN, placed close to the pins is usually sufficient. Higher values of CIN can be used to further reduce
the voltage drop.
Output Capacitor
Due to the integral body diode in the PMOS switch, a CIN greater than CL is highly recommended. A CL greater
than CIN can cause VOUT to exceed VIN when the system supply is removed. This could result in current flow
through the body diode from VOUT to VIN.
Board Layout
For best performance, all traces should be as short as possible. To be most effective, the input and output
capacitors should be placed close to the device to minimize the effects that parasitic trace inductances may have
on normal and short-circuit operation. Using wide traces for VIN, VOUT, and GND helps minimize the parasitic
electrical effects along with minimizing the case to ambient thermal impedance.
Undervoltage Lockout
The undervoltage lockout turns off the switch if the input voltage drops below the under-voltage lockout
threshold. With the ON pin active, the input voltage rising above the undervoltage lockout threshold causes a
controlled turn-on of the switch, which limits current overshoots.
20
Copyright 2010, Texas Instruments Incorporated
Product Folder Link(s): TPS22934
相關PDF資料 |
PDF描述 |
|---|---|
| TPS22942DCKRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS22945DCKR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS22949ADRGR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2301IPWRG4 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPS2300IPWRG4 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS22934YZVT | 功能描述:電源開關 IC - 配電 Ultra-SmallLo VIN Ultra-Lo rON Load Sw RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| TPS22941DCKR | 功能描述:電源開關 IC - 配電 Low-Inp Vltg 40mA Current Ltd Load Sw RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| TPS22942DCKR | 功能描述:電源開關 IC - 配電 Low-Inp Vltg Crnt Ltd load switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| TPS22942DCKR | 制造商:Texas Instruments 功能描述:Load Switch IC 制造商:Texas Instruments 功能描述:IC, CURRENT LIMITED LOAD SW 5.5V SC-70-5 |
| TPS22942DCKRG4 | 功能描述:電源開關 IC - 配電 Low-Inp Vltg Crnt Ltd load switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。