- 您現在的位置：買賣IC網 > PDF目錄69502 > TPS22913CYZVT (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4 PDF資料下載
參數資料
| 型號： | TPS22913CYZVT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4 |
| 封裝： | 0.90 X 0.90 MM, 0.50 MM PITCH, GREEN, DSBGA-4 |
| 文件頁數： | 9/22頁 |
| 文件大?。?/td> | 870K |
| 代理商： | TPS22913CYZVT |
RC
ON( VIN)
0.044V
I
R
=
SLVSB20
– SEPTEMBER 2011
APPLICATION INFORMATION
On/Off Control
The ON pin controls the state of the switch. Asserting ON high enables the switch. ON is active high and has a
low threshold, making it capable of interfacing with low-voltage signals. The ON pin is compatible with standard
GPIO logic threshold. It can be used with any microcontroller with 1.8-V, 2.5-V or 3.3-V GPIOs.
Input Capacitor
To limit the voltage drop on the input supply caused by transient inrush currents when the switch turns on into a
discharged load capacitor or short-circuit, a capacitor needs to be placed between VIN and GND. A 1-
μF ceramic
capacitor, CIN, placed close to the pins is usually sufficient. Higher values of CIN can be used to further reduce
the voltage drop.
Output Capacitor
A CIN to CL ratio of 10 to 1 is recommended for minimizing VIN dip caused by inrush currents during startup.
Output Pull-Down
The output pulldown is active when the user is turning off the main pass FET. The pulldown discharges the
output rail to approximately 10% of the rail, and then the output pulldown is automatically disconnected to
optimize the shutdown current.
Under-Voltage Lockout
The under-voltage lockout turns-off the switch if the input voltage drops below the under-voltage lockout
threshold. With the ON pin active the input voltage rising above the under-voltage lockout threshold will cause a
controlled turn-on of the switch which limits current over-shoots. During under-voltage lockout (UVLO), no
reverse current can flow as the body diode is not engaged.
Reverse Current Protection
In a scenario where VOUT is greater than VIN, there could be reverse current through the body diode of the PMOS
FET. The TPS22913 monitors the current through the FET and shuts off the FET when a reverse current is
detected. The FET, and the output, resumes normal operation when the reverse current scenario is no longer
present. When the reverse current protection (RCP) is active, no reverse current can flow as the body diode is
not engaged. During under-voltage lockout (UVLO), or when the switch is disabled, no reverse current can flow
as the body diode is not engaged.
Use the following formula to calculate the amount of reverse current for a particular application:
Where,
IRC is the amount of reverse current,
RON(VIN) is the on-resistance at the VIN of the reverse current condition.
Board Layout
For best performance, all traces should be as short as possible. To be most effective, the input and output
capacitors should be placed close to the device to minimize the effects that parasitic trace inductances may have
on normal operation. Using wide traces for VIN, VOUT, and GND helps minimize the parasitic electrical effects
along with minimizing the case to ambient thermal impedance.
Copyright
2011, Texas Instruments Incorporated
17
Product Folder Link(s) :TPS22913
相關PDF資料 |
PDF描述 |
|---|---|
| TPS22913BYZVT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4 |
| TPS22913AYZVR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4 |
| TPS22924BYZR | POWER SUPPLY SUPPORT CKT, PBGA6 |
| TPS22924CYZPR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA6 |
| TPS2310IPW | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS22914BEVM-078 | 功能描述:TPS22914B - Power Management, Power Distribution Switch (Load Switch) Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 主要用途:電源管理，配電開關（負載開關） 嵌入式:否 使用的 IC/零件:TPS22914B 主要屬性:- 輔助屬性:- 所含物品:板 標準包裝:1 |
| TPS22914BYFPR | 功能描述:IC LOAD SWITCH 5.5V 4DSBGA 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 開關類型:通用 輸出數:1 比率 - 輸入:輸出:1:1 輸出配置:高端 輸出類型:N 通道 接口:開/關 電壓 - 負載:1.05 V ~ 5.5 V 電壓 - 電源（Vcc/Vdd）:不需要 電流 - 輸出（最大值）:2A 導通電阻（典型值）:37 毫歐 輸入類型:非反相 特性:壓擺率受控型 故障保護:- 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:4-XFBGA，DSBGA 供應商器件封裝:4-DSBGA 標準包裝:1 |
| TPS22914BYFPT | 功能描述:IC LOAD SWITCH 5.5V 4DSBGA 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 開關類型:通用 輸出數:1 比率 - 輸入:輸出:1:1 輸出配置:高端 輸出類型:N 通道 接口:開/關 電壓 - 負載:1.05 V ~ 5.5 V 電壓 - 電源（Vcc/Vdd）:不需要 電流 - 輸出（最大值）:2A 導通電阻（典型值）:37 毫歐 輸入類型:非反相 特性:壓擺率受控型 故障保護:- 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:4-XFBGA，DSBGA 供應商器件封裝:4-DSBGA 標準包裝:1 |
| TPS22914CEVM-078 | 功能描述:TPS22914C - Power Management, Power Distribution Switch (Load Switch) Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 主要用途:電源管理，配電開關（負載開關） 嵌入式:否 使用的 IC/零件:TPS22914C 主要屬性:1 通道（單路） 輔助屬性:- 所含物品:板 標準包裝:1 |
| TPS22914CYFPR | 功能描述:IC LOAD SWITCH 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 開關類型:通用 輸出數:1 比率 - 輸入:輸出:1:1 輸出配置:高端 輸出類型:N 通道 接口:開/關 電壓 - 負載:1.05 V ~ 5.5 V 電壓 - 電源（Vcc/Vdd）:不需要 電流 - 輸出（最大值）:2A 導通電阻（典型值）:37 毫歐 輸入類型:非反相 特性:壓擺率受控型 故障保護:- 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:4-XFBGA，DSBGA 供應商器件封裝:4-DSBGA 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。