參數資料
型號： TPS22906YZVR
廠商： TEXAS INSTRUMENTS INC
元件分類： 電源管理
英文描述： 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4
封裝： 0.90 X 0.90 MM, 0.50 MM HEIGHT, 0.50 MM PITCH, LEAD FREE, WCSP-4
文件頁數： 8/20頁
文件大?。?/td> 620K
代理商： TPS22906YZVR
APPLICATION INFORMATION
ON/OFF Control
Input Capacitor
Output Capacitor
Board Layout
SLVS921 – MARCH 2009................................................................................................................................................................................................... www.ti.com
The ON pin controls the state of the switch. Activating ON continuously holds the switch in the on state so long
as there is no fault. ON is active HI and has a low threshold making it capable of interfacing with low voltage
signals. The ON pin is compatible with standard GPIO logic threshold. It can be used with any microcontroller
with 1.2-V, 1.8-V, 2.5-V, or 3.3-V GPIOs.
To limit the voltage drop on the input supply caused by transient in-rush currents when the switch turns on into a
discharged load capacitor or short-circuit, a capacitor needs to be placed between VIN and GND. A 1-F ceramic
capacitor, CIN, place close to the pins is usually sufficient. Higher values of CIN can be use to further reduce the
voltage drop during high current application. When switching heavy loads, it is recommended to have an input
capacitor approximately 10 times higher than the output capacitor to avoid excessive voltage drop.
Due to the integral body diode in the PMOS switch, a CIN greater than CL is highly recommended. A CL greater
than CIN can cause VOUT to exceed VIN when the system supply is removed. This could result in current flow
through the body diode from VOUT to VIN.
For best performance, all traces should be as short as possible. To be most effective, the input and output
capacitors should be placed close to the device to minimize the effects that parasitic trace inductances may have
on normal and short-circuit operation. Using wide traces for VIN, VOUT, and GND helps minimize the parasitic
electrical effects along with minimizing the case to ambient thermal impedance.
16
Copyright 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS22906
相關PDF資料
PDF描述
TPS22913BYZVR 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4
TPS22913CYZVR 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4
TPS22913CYZVT 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4
TPS22913BYZVT 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4
TPS22913AYZVR 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4
相關代理商/技術參數
參數描述
TPS22907EVM-025 制造商:Texas Instruments 功能描述:TPS22907EVM-025 - Boxed Product (Development Kits) 制造商:Texas Instruments 功能描述:MODULE EVAL FOR TPS22907-025 制造商:Texas Instruments 功能描述:TPS22907 EVAL MOD
TPS22907YZT 制造商:Texas Instruments 功能描述:ULTRA SMALL, LOW INPUT VOLTAGE, LOW RON LOAD SWITCH - Tape and Reel
TPS22907YZTR 功能描述:電源開關 IC - 配電 Ultra Small Low Inp Vltg Lo rON Load Sw RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
TPS22907YZTT 功能描述:電源開關 IC - 配電 Ultra Small Low Inp Vltg Lo rON Load Sw RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
TPS22907YZTT 制造商:Texas Instruments 功能描述:Power Load Switch IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*