- 您現在的位置：買賣IC網 > PDF目錄98279 > TPS22904YFPR (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBGA4 PDF資料下載
參數資料
| 型號： | TPS22904YFPR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBGA4 |
| 封裝： | 0.80 X 0.80 MM, 0.50 MM HEIGHT, 0.40 MM PITCH, GREEN PACKAGE, DSBGA-4 |
| 文件頁數： | 4/17頁 |
| 文件大小： | 822K |
| 代理商： | TPS22904YFPR |
SLVS827C – FEBRUARY 2009 – REVISED APRIL 2010
www.ti.com
APPLICATION INFORMATION
ON/OFF Control
The ON pin controls the state of the switch. Activating ON continuously holds the switch in the on state as there
is no fault. ON is active-high and has a low threshold, making it capable of interfacing with low-voltage signals.
The ON pin is compatible with standard GPIO logic thresholds. It can be used with any microcontroller with
1.2-V, 1.8-V, 2.5-V, or 3.3-V GPIOs.
Input Capacitor (Optional)
To limit the voltage drop on the input supply caused by transient in-rush currents when the switch turns on into a
discharged load capacitor or short-circuit, a capacitor needs to be placed between VIN and GND. A 1-mF ceramic
capacitor, CIN, placed close to the pins, is usually sufficient. Higher values of CIN can be used to further reduce
the voltage drop during high-current application. When switching heavy loads, it is recommended to have an
input capacitor about 10 times higher than the output capacitor to avoid excessive voltage drop.
Output Capacitor (Optional)
Due to the integral body diode in the PMOS switch, a CIN greater than CL is highly recommended. A CL greater
than CIN can cause VOUT to exceed VIN when the system supply is removed. This could result in current flow
through the body diode from VOUT to VIN.
Board Layout
For best performance, all traces should be as short as possible. To be most effective, the input and output
capacitors should be placed close to the device to minimize the effects that parasitic trace inductances may have
on normal and short-circuit operation. Using wide traces for VIN, VOUT, and GND helps minimize the parasitic
electrical effects along with minimizing the case-to-ambient thermal impedance.
12
Copyright 2009–2010, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS22934YZVR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA4 |
| TPS22942DCKRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS22945DCKR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS22949ADRGR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2301IPWRG4 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS22904YFPT | 功能描述:電源開關 IC - 配電 Ultra-Small Lo-Vltg Low rON Load Switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| TPS22906YZVR | 功能描述:電源開關 IC - 配電 Ultra-Small,Low-In Vltg,Lo rON Load Sw RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| TPS22907EVM-025 | 制造商:Texas Instruments 功能描述:TPS22907EVM-025 - Boxed Product (Development Kits) 制造商:Texas Instruments 功能描述:MODULE EVAL FOR TPS22907-025 制造商:Texas Instruments 功能描述:TPS22907 EVAL MOD |
| TPS22907YZT | 制造商:Texas Instruments 功能描述:ULTRA SMALL, LOW INPUT VOLTAGE, LOW RON LOAD SWITCH - Tape and Reel |
| TPS22907YZTR | 功能描述:電源開關 IC - 配電 Ultra Small Low Inp Vltg Lo rON Load Sw RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。