- 您現在的位置：買賣IC網 > PDF目錄69500 > TPS2075R (TEXAS INSTRUMENTS INC) 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 PDF資料下載
參數資料
| 型號： | TPS2075R |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
| 封裝： | PLASTIC, SSOP-24 |
| 文件頁數： | 19/24頁 |
| 文件大?。?/td> | 389K |
| 代理商： | TPS2075R |
TPS2074, TPS2075
FOUR-PORT USB HUB POWER CONTROLLERS
SLVS288 – SEPTEMBER 2000
4
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
detailed description
BP
The bus-powered supply input (BP) serves as the source for the internal 3.3-V LDO and for all logic functions
in the device. In bus-powered mode, BP also serves as the source for all the outputs (OUTx). If BP is below the
undervoltage threshold, all power switches will turn off and the LDO will be disabled. BP must be connected to
a voltage source in order for the device to operate.
SP
The self-powered supply input (SP) serves as the source for all the outputs (OUTx) in self-powered mode. The
enable logic for the SP switches requires that BP be connected to a voltage source.
OUT1, OUT2, OUT2, OUT4
OUTx are the outputs of the integrated power switches.
3.3V_OUT
The internal 3.3-V LDO output can be used to supply up to 100 mA current to low-power functions, such as hub
controllers.
DP0_RST
DP0_RST functions as a hub reset when a 1.5-k
resistor is connected between DP0_RST and the upstream
DP0 data line in a hub system. To provide a clean attach signal on DP0 data line, the DP0_RST output goes
low momentarily (because of the upstream pulldown resistor) to discharge any parasitic charge on the cable,
then goes to 3-state and finally outputs a high signal. The low and Hi-Z pulse widths are adjustable using a
capacitor between PG_DLY and ground, and are approximately 50% of the power-good time delay. Detachment
is signaled by a Hi-Z on DP0_RST. Both DP0_RST and PG will transition high at the same time.
Power Good (PG)
The power good (PG) function serves as a reset for a USB hub controller. PG is asserted low when the output
voltage on the internal voltage regulator is below a fixed threshold. A time delay to ensure a stable output voltage
before PG goes high is adjustable using a small-value ceramic capacitor from PG_DLY to ground.
PG_DLY
PG_DLY connects to an external capacitor to adjust the time delay for PG and DP0_RST. A 0.47-
F capacitor
is recommended.
BP_DIS
BP_DIS is used to enable or disable the autoswitching function between bus-powered mode and self-powered
mode. When BP_DIS is connected low and the voltage on SP is greater than the undervoltage-lockout (UVLO)
threshold, the device will switch to self-powered operation automatically; if the SP voltage falls lower than the
UVLO threshold, the device will switch to bus-powered operation. When BP_DIS is connected high, the
autoswitching function is disabled and the device will not autoswitch to bus-powered operation if the SP voltage
is below the UVLO threshold.
BPMODE or BPMODE
BPMODE (TPS2074) or BPMODE (TPS2075) is an output that signals when the device is in bus-powered
mode. The logic state is set according to the voltages on BP, SP, and BP_DIS. For the TPS2074, BPMODE
outputs a low signal to indicate bus-powered mode or a high signal to indicate self-powered mode. For the
TPS2075, BPMODE outputs a high signal to indicate bus-powered mode or a low signal to indicate self-powered
mode. This output can be used to inform a USB hub controller to configure for bus-powered mode or
self-powered mode.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2074R | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
| TPS2102DBVTG4 | POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS2103DBVRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS2103DBV | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS2102DG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2080D | 功能描述:電源開關 IC - 配電 0.7A 2.7-5.5V Dual Hi-Side MOSFET RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| TPS2080D | 制造商:Texas Instruments 功能描述:IC DUAL POWER DIST SW 8-SOIC 制造商:Texas Instruments 功能描述:IC, DUAL POWER DIST SW 8-SOIC 制造商:Texas Instruments 功能描述:IC, DUAL POWER DIST SW 8-SOIC; Power Load Switch Type:High Side; Input Voltage:5.5V; Current Limit:1A; On State Resistance:0.08ohm; Distribution Switch Case Style:SOIC; No. of Pins:8; Thermal Protection:Yes; On / Enable Input ;RoHS Compliant: Yes |
| TPS2080DG4 | 功能描述:電源開關 IC - 配電 0.7A 2.7-5.5V Dual Hi-Side MOSFET RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| TPS2080DR | 功能描述:電源開關 IC - 配電 0.7A 2.7-5.5V Dual Hi-Side MOSFET RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| TPS2080DRG4 | 功能描述:電源開關 IC - 配電 0.7A 2.7-5.5V Dual Hi-Side MOSFET RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。