- 您現在的位置：買賣IC網 > PDF目錄365910 > TPA6030A4 3-W Stereo Audio Power Amplifier with Advanced DC Volume Control PDF資料下載
參數資料
| 型號： | TPA6030A4 |
| 英文描述： | 3-W Stereo Audio Power Amplifier with Advanced DC Volume Control |
| 中文描述： | 3 - W立體聲音頻功率放大器與先進的直流音量控制 |
| 文件頁數： | 19/33頁 |
| 文件大?。?/td> | 469K |
| 代理商： | TPA6030A4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
TPA6011A4
SLOS392
–
FEBRUARY 2002
19
www.ti.com
APPLICATION INFORMATION
shutdown modes
The TPA6011A4 employs a shutdown mode of operation designed to reduce supply current (I
DD
) to the absolute
minimum level during periods of nonuse for battery-power conservation. The SHUTDOWN input terminal
should be held high during normal operation when the amplifier is in use. Pulling SHUTDOWN low causes the
outputs to mute and the amplifier to enter a low-current state, I
DD
= 20
μ
A. SHUTDOWN should never be left
unconnected because amplifier operation would be unpredictable.
Table 3. HP/LINE, SE/BTL, and Shutdown Functions
INPUTS
SE/BTL
AMPLIFIER STATE
HP/LINE
SHUTDOWN
INPUT
OUTPUT
X
X
Low
X
Mute
Low
Low
High
Line
BTL
Low
High
High
Line
SE
High
Low
High
HP
BTL
High
High
High
HP
SE
Inputs should never be left unconnected.
X = don
’
t care
NOTE: The
Low
and
High
trip levels can be found in the
recommended operating conditions
table.
FADE operation
For design flexibility, a fade mode is provided to slowly ramp up the amplifier gain when coming out of shutdown
mode and conversely ramp the gain down when going into shutdown. This mode provides a smooth transition
between the active and shutdown states and virtually eliminates any pops or clicks on the outputs.
When the FADE input is a logic low, the device is placed into fade-on mode. A logic high on this pin places the
amplifier in the fade-off mode. The voltage trip levels for a logic low (V
IL
) or logic high (V
IH
) can be found in the
recommended operating conditions
table on page 4.
When a logic low is applied to the FADE pin and a logic low is then applied on the SHUTDOWN pin, the channel
gain steps down from gain step to gain step at a rate of two clock cycles per step. With a nominal internal clock
frequency of 58 Hz, this equates to 34 ms (1/24 Hz) per step. The gain steps down until the lowest gain step
is reached. The time it takes to reach this step depends on the gain setting prior to placing the device in
shutdown. For example, if the amplifier is in the highest gain mode of 20 dB, the time it takes to ramp down the
channel gain is 1.05 seconds. This number is calculated by taking the number of steps to reach the lowest gain
from the highest gain, or 31 steps, and multiplying by the time per step, or 34 ms.
After the channel gain is stepped down to the lowest gain, the amplifier begins discharging the bypass capacitor
from the nominal voltage of V
DD
/2 to ground. This time is dependent on the value of the bypass capacitor. For
a 0.47-
μ
F capacitor that is used in the application diagram in Figure 27, the time is approximately 500 ms. This
time scales linearly with the value of bypass capacitor. For example, if a 1-
μ
F capacitor is used for bypass, the
time period to discharge the capacitor to ground is twice that of the 0.47-
μ
F capacitor, or 1 second. Figure 30
below is a waveform captured at the output during the shutdown sequence when the part is in fade-on mode.
The gain is set to the highest level and the output is at V
DD
when the amplifier is shut down.
When a logic high is placed on the SHUTDOWN pin and the FADE pin is still held low, the device begins the
start-up process. The bypass capacitor will begin charging. Once the bypass voltage reaches the final value
of V
DD
/2, the gain increases in 2-dB steps from the lowest gain level to the gain level set by the dc voltage applied
to the VOLUME, SEDIFF, and SEMAX pins.
相關PDF資料 |
PDF描述 |
|---|---|
| TPA6030A4PWP | Slide |
| TPA6100A2 | 50-mW Ultra-Low Voltage Audio Power Amp |
| TPA6110A2DGNR | Switchlocks |
| TPA6111A2DGNR | Rotary Keylock Switch; Key Removal Position:1; Circuitry:SPST; Indexing:90; Contact Current Max:4A; Contact Rating:4A; Leaded Process Compatible:Yes; Mounting Type:Solder Lug; No. of Switch Positions:1; Number of Positions:1 |
| TPA6111A2DR | Rotary Keylock Switch; Key Removal Position:1, 2; Circuitry:SPST; Indexing:90; Contact Current Max:4A; Contact Rating:4A; Leaded Process Compatible:Yes; Mounting Type:Solder Lug; No. of Switch Positions:2; Number of Positions:2 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA6030A4_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-2 STEREO AUDIO POWER AMPLIFIER WITH ADVANCED DC VOLUME CONTROL |
| TPA6030A4EVM | 功能描述:音頻 IC 開發工具 TPA6030A4 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TPA6030A4PWP | 功能描述:音頻放大器 Wide Supply Voltage Low Power Class-AB RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6030A4PWPG4 | 功能描述:音頻放大器 Wide Supply Voltage Low Power Class-AB RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6030A4PWPR | 功能描述:音頻放大器 Wide Supply Voltage Low Power Class-AB RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。