參數資料
型號： TPA0312PWP
廠商： TEXAS INSTRUMENTS INC
元件分類： 音頻控制
英文描述： 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24
封裝： GREEN, PLASTIC, HTSSOP-24
文件頁數： 16/36頁
文件大?。?/td> 791K
代理商： TPA0312PWP
www.ti.com
RL
CC
VO(PP)
VDD
–3 dB
fc
SINGLE-ENDED OPERATION
BTL AMPLIFIER EFFICIENCY
V(LRMS)
VO
IDD
IDD(avg)
TPA0312
SLOS335A – DECEMBER 2000 – REVISED OCTOBER 2004
Figure 40. Single-Ended Configuration and Frequency Response
Increasing power to the load does carry a penalty of increased internal power dissipation. The increased
dissipation is understandable considering that the BTL configuration produces 4
× the output power of the SE
configuration. Internal dissipation versus output power is discussed further in the Crest Factor and Thermal
Considerations section.
In SE mode the load is driven from the primary amplifier output for each channel (OUT+, terminals 21 and 4).
The amplifier switches single-ended operation when the SE/BTL terminal is held high. This puts the negative
outputs in a high-impedance state, and reduces the amplifier's gain to 4.1 dB.
Class-AB amplifiers are notoriously inefficient. The primary cause of these inefficiencies is voltage drop across
the output stage transistors. There are two components of the internal voltage drop. One is the headroom or dc
voltage drop that varies inversely to output power. The second component is due to the sine-wave nature of the
output. The total voltage drop can be calculated by subtracting the RMS value of the output voltage from VDD.
The internal voltage drop multiplied by the RMS value of the supply current, IDDrms, determines the internal
power dissipation of the amplifier.
An easy-to-use equation to calculate efficiency starts out as being equal to the ratio of power from the power
supply to the power delivered to the load. To accurately calculate the RMS and average values of power in the
load and in the amplifier, the current and voltage waveform shapes must first be understood (see Figure 41).
Figure 41. Voltage and Current Waveforms for BTL Amplifiers
Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are
different between SE and BTL configurations. In an SE application, the current waveform is a half-wave rectified
shape, whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different.
Keep in mind that for most of the waveform both the push and pull transistors are not on at the same time, which
supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform.
The following equations are the basis for calculating amplifier efficiency.
23
相關PDF資料
PDF描述
TPA0312PWPG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24
TPA0312PWPRG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24
TPA032D02DCAR 10 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO48
TPA032D02DCA 10 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO48
TPA032D02DCAG4 10 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO48
相關代理商/技術參數
參數描述
TPA0312PWPG4 功能描述:音頻放大器 St 2W Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0312PWPR 功能描述:音頻放大器 St 2W Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0312PWPRG4 功能描述:音頻放大器 St 2W Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA032D01 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-W MONO CLASS-D AUDIO POWER AMPLIFIER
TPA032D01_07 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-W MONO CLASS-D AUDIO POWER AMPLIFIER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*