參數資料
型號: TPA0233DGQ
廠商: TEXAS INSTRUMENTS INC
元件分類: 音頻/視頻放大
英文描述: 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10
封裝: GREEN, PLASTIC, MSOP-10
文件頁數: 7/26頁
文件大小: 711K
代理商: TPA0233DGQ
TPA0233
2W MONO AUDIO POWER AMPLIFIER
WITH HEADPHONE DRIVE
SLOS278D JANUARY 2000 REVISED NOVEMBER 2002
15
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
bridged-tied load versus single-ended mode (continued)
In a typical computer sound channel operating at 5 V, bridging raises the power into an 8-
speaker from a
singled-ended (SE, ground reference) limit of 250 mW to 1 W. In sound power, that is a 6-dB improvement—
which is loudness that can be heard. In addition to increased power, there are frequency response concerns.
Consider the single-supply SE configuration shown in Figure 25. A coupling capacitor is required to block the
dc offset voltage from reaching the load. These capacitors can be quite large (approximately 33
F to 1000 F)
so they tend to be expensive, heavy, occupy valuable PCB area, and have the additional drawback of limiting
low-frequency performance of the system. This frequency limiting effect is due to the high-pass filter network
created with the speaker impedance and the coupling capacitance and is calculated with equation 8.
fc +
1
2
pR
L
C
(C)
(8)
For example, a 68-
F capacitor with an 8- speaker would attenuate low frequencies below 293 Hz. The BTL
configuration cancels the dc offsets, which eliminates the need for the blocking capacitors. Low-frequency
performance is then limited only by the input network and speaker response. Cost and PCB space are also
minimized by eliminating the bulky coupling capacitor.
RL
C(C)
VO(PP)
VDD
3 dB
fc
Figure 25. Single-Ended Configuration and Frequency Response
Increasing power to the load does carry a penalty of increased internal power dissipation. The increased
dissipation is understandable considering that the BTL configuration produces 4
× the output power of the SE
configuration. Internal dissipation versus output power is discussed further in the crest factor and thermal
considerations section.
single-ended (stereo) operation
In SE (stereo) mode (see Figure 24 and Figure 25), the load is driven from the primary amplifier output for each
channel (LO and RO, terminals 6 and 10).
The amplifier switches to single-ended operation when the ST/MN terminal is held high.
input operation
The input allows stereo inputs to be applied to the amplifier. When the ST/MN terminal is held high, the inputs
(LIN and RIN) drive the outputs as LO and RO in stereo mode. When the ST/MN terminal is held low, the inputs
are surrounded internally to create the mono BTL signal, driving the outputs as MO+ and MO.
相關PDF資料
PDF描述
TPA0233DGQRG4 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10
TPA0233DGQG4 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10
TPA0242PWP 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24
TPA0242PWPR 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24
TPA0242PWPRG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24
相關代理商/技術參數
參數描述
TPA0233DGQG4 功能描述:音頻放大器 Mono Class-AB w/Ster Hdphn Drv Summed Inp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0233DGQR 功能描述:音頻放大器 Mono Class-AB w/Ster Hdphn Drv Summed Inp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0233DGQRG4 功能描述:音頻放大器 Mono Class-AB w/Ster Hdphn Drv Summed Inp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0233EVM 功能描述:音頻 IC 開發工具 TPA0233 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TPA0233G 制造商:ON Semiconductor 功能描述:THY T0220 SPECIAL SCR