TPA0211
2-W MONO AUDIO POWER AMPLIFIER
SLOS275D – JANUARY 2000 – REVISED NOVEMBER 2002
3
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, VDD
6 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI
–0.3 V to VDD +0.3 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation
internally limited (see Dissipation Rating Table)
. . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA
– 40
°C to 85°C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating junction temperature range, TJ
– 40
°C to 150°C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg
–65
°C to 150°C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
260
°C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
DERATING FACTOR
TA = 70°C
TA = 85°C
DGN
2.14 W
17.1 mW/
°C
1.37 W
1.11 W
See the Texas Instruments document, PowerPAD Thermally Enhanced Package Application Report
(SLMA002), for more information on the PowerPAD
package. The thermal data was measured on a PCB
layout based on the information in the section entitled Texas Instruments Recommended Board for PowerPAD
on page 33 of that document.
recommended operating conditions
MIN
MAX
UNIT
Supply voltage, VDD
2.5
5.5
V
SE/BTL
VDD = 3 V
2.7
High-level input voltage, VIH
SE/BTL
VDD = 5 V
4.5
V
High level in ut voltage, VIH
SHUTDOWN
2
V
SE/BTL
VDD = 3 V
1.65
Low-level input voltage, VIL
SE/BTL
VDD = 5 V
2.75
V
Low level in ut voltage, VIL
SHUTDOWN
0.8
V
Operating free-air temperature, TA
– 40
85
°C
electrical characteristics at specified free-air temperature, VDD = 3 V, TA = 25°C (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
|VOO|
Output offset voltage (measured
differentially)
SE/BTL = 0 V, SHUTDOWN = 2 V,
RL = 8 , Inputs floating
30
mV
IDD(BTL)
Supply current, BTL mode
SE/BTL = 1.375 V, SHUTDOWN = 2 V, VDD = 2.5 V
4
6
mA
IDD(SE)
Supply current, SE mode
SE/BTL = 2.25 V, SHUTDOWN = 2 V, VDD = 2.5 V
2
4
mA
IDD(SD)
Supply current, shutdown mode
SHUTDOWN = 0 V, SE/BTL = 3 V
1
10
A
|I
|
High level input current
SHUTDOWN
VDD = 3.3 V, VI = VDD
1
A
|IIH|
High-level input current
SE/BTL
VDD = 3.3 V, VI = VDD
1
A
|I |
Low level input current
SHUTDOWN
VDD = 3.3 V, VI = 0 V
1
A
|IIL|
Low-level input current
SE/BTL
VDD = 3.3 V, VI = 0 V
1
A
RF
Feedback resistor
VDD = 2.5 V, SHUTDOWN = 2 V, SE/BTL = 0 V,
RL = 4
45
50
60
k
PowerPAD is a trademark of Texas Instruments.