參數資料
型號： TMS320F28044GGMQ
廠商： Texas Instruments, Inc.
元件分類： 數字信號處理
英文描述： Digital Signal Processor
中文描述： 數字信號處理器
文件頁數： 23/105頁
文件大?。?/td> 768K
代理商： TMS320F28044GGMQ
www.ti.com
A
3.2.3
Peripheral Bus
3.2.4
Real-Time JTAG and Analysis
3.2.5
Flash
3.2.6
M0, M1 SARAMs
3.2.7
L0, L1 SARAMs
TMS320F28044
Digital Signal Processor
SPRS357A–AUGUST 2006–REVISED OCTOBER 2006
To enable migration of peripherals between various Texas Instruments (TI) DSP family of devices, the
28044 device adopts a peripheral bus standard for peripheral interconnect. The peripheral bus bridge
multiplexes the various busses that make up the processor Memory Bus into a single bus consisting of 16
address lines and 16 or 32 data lines and associated control signals. Two versions of the peripheral bus
are supported on the 28044. One version only supports 16-bit accesses (called peripheral frame 2). The
other version supports both 16- and 32-bit accesses (called peripheral frame 1).
The 28044 implements the standard IEEE 1149.1 JTAG interface. Additionally, the device supports
real-time mode of operation whereby the contents of memory, peripheral and register locations can be
modified while the processor is running and executing code and servicing interrupts. The user can also
single step through non-time critical code while enabling time-critical interrupts to be serviced without
interference. The 28044 implements the real-time mode in hardware within the CPU. This is a unique
feature to the 28044, no software monitor is required. Additionally, special analysis hardware is provided
which allows the user to set hardware breakpoint or data/address watch-points and generate various
user-selectable break events when a match occurs.
The F28044 contains 64K x 16 of embedded flash memory, segregated into four 16K X 16 sectors. Both
devices also contain a single 1K x 16 of OTP memory at address range 0x3D 7800 – 0x3D 7BFF. The
user can individually erase, program, and validate a flash sector while leaving other sectors untouched.
However, it is not possible to use one sector of the flash or the OTP to execute flash algorithms that
erase/program other sectors. Special memory pipelining is provided to enable the flash module to achieve
higher performance. The flash/OTP is mapped to both program and data space; therefore, it can be used
to execute code or store data information. Note that addresses 0x3F7FF0 – 0x3F7FF5 are reserved for
data variables and should not contain program code.
NOTE
The F28044 Flash and OTP wait-states can be configured by the application. This allows
applications running at slower frequencies to configure the flash to use fewer wait-states.
Flash effective performance can be improved by enabling the flash pipeline mode in the
Flash options register. With this mode enabled, effective performance of linear code
execution will be much faster than the raw performance indicated by the wait-state
configuration alone. The exact performance gain when using the Flash pipeline mode is
application-dependent.
For more information on the Flash options, Flash wait-state, and OTP wait-state registers,
see the
TMS320x280x, 2801x, 2804x System Control and Interrupts Reference Guide
(literature number SPRU712).
The F28044 device contains these two blocks (M0/M1) of single access memory, each 1K x 16 in size.
The stack pointer points to the beginning of block M1 on reset. The M0 and M1 blocks, like all other
memory blocks on C28x devices, are mapped to both program and data space. Hence, the user can use
M0 and M1 to execute code or for data variables. The partitioning is performed within the linker. The C28x
device presents a unified memory map to the programmer. This makes for easier programming in
high-level languages.
The F28044 device contains an additional 8K x 16 of single-access RAM, divided into 2 blocks (L0-4K,
L1-4K). Each block can be independently accessed to minimize CPU pipeline stalls. Each block is
mapped to both program and data space.
Submit Documentation Feedback
Functional Overview
23
相關PDF資料
PDF描述
TMS320F28044GGMS Digital Signal Processor
TMS320F28044PZQ Digital Signal Processor
TMS320LC545 Digital Signal Processors(20/25ns指令周期， 高性能，大并行度，特殊指令集可有效實現多種復雜算法及應用的DSP)
TMS320LC546 Digital Signal Processors(20/25ns指令周期， 高性能，大并行度，特殊指令集可有效實現多種復雜算法及應用的DSP)
TMS320LC57S Digital Signal Processors(35/50ns指令周期，并行邏輯單元，可編程PLL，全雙工同步串行口的DSP)
相關代理商/技術參數
參數描述
TMS320F28044PZA 功能描述:數字信號處理器和控制器 - DSP, DSC 32-Bit DSC w/ 128KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320F28044PZS 功能描述:數字信號處理器和控制器 - DSP, DSC 32-Bit DSC w/ 128KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320F28045PZA 制造商:Texas Instruments 功能描述:- Trays
TMS320F28045PZS 制造商:Texas Instruments 功能描述:- Trays
TMS320F28050PNQ 制造商:Texas Instruments 功能描述:GIZMO
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*