- 您現在的位置：買賣IC網 > PDF目錄359296 > TMS320C6211GNZ167 (Texas Instruments, Inc.) POT 5.0K OHM 3/8 SQ CERM SL ST PDF資料下載
參數資料
| 型號： | TMS320C6211GNZ167 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | POT 5.0K OHM 3/8 SQ CERM SL ST |
| 中文描述： | 定點數字信號處理器 |
| 文件頁數： | 56/123頁 |
| 文件大?。?/td> | 1205K |
| 代理商： | TMS320C6211GNZ167 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁
www.ti.com
Result Registers
EPWMSOCB
S/W
GPIO/XINT2
_ADCSOC
EPWMSOCA
S/W
Sequencer 2
Sequencer 1
SOC
SOC
ADC Control Registers
70B7h
70B0h
70AFh
70A8h
Result Reg 15
Result Reg 8
Result Reg 7
Result Reg 1
Result Reg 0
Module
ADC
12-Bit
Analog
MUX
ADCINA0
ADCINA7
ADCINB0
ADCINB7
System
Control Block
High-Speed
Prescaler
HSPCLK
ADCENCLK
DSP
SYSCLKOUT
S/H
S/H
HALT
TMS320F2808, TMS320F2806
TMS320F2801, UCD9501
Digital Signal Processors
SPRS230F–OCTOBER 2003–REVISED SEPTEMBER 2005
Figure 4-7. Block Diagram of the ADC Module
To obtain the specified accuracy of the ADC, proper board layout is very critical. To the best extent
possible, traces leading to the ADCIN pins should not run in close proximity to the digital signal paths.
This is to minimize switching noise on the digital lines from getting coupled to the ADC inputs.
Furthermore, proper isolation techniques must be used to isolate the ADC module power pins ( V
DD1A18
,
V
DD2A18
, V
DDA2
, V
DDAIO
) from the digital supply.
Figure 4-8
shows the ADC pin connections for the 280x
devices.
NOTE
1. The ADC registers are accessed at the SYSCLKOUT rate. The internal timing of the
ADC module is controlled by the high-speed peripheral clock (HSPCLK).
2. The behavior of the ADC module based on the state of the ADCENCLK and HALT
signals is as follows:
–
ADCENCLK:
On reset, this signal will be low. While reset is active-low (XRS) the
clock to the register will still function. This is necessary to make sure all registers
and modes go into their default reset state. The analog module, however, will be
in a low-power inactive state. As soon as reset goes high, then the clock to the
registers will be disabled. When the user sets the ADCENCLK signal high, then
the clocks to the registers will be enabled and the analog module will be enabled.
There will be a certain time delay (ms range) before the ADC is stable and can be
used.
–
HALT:
This mode only affects the analog module. It does not affect the registers.
In this mode, the ADC module goes into low-power mode. This mode also will stop
the clock to the CPU, which will stop the HSPCLK; therefore, the ADC register
logic will be turned off indirectly.
56
Peripherals
相關PDF資料 |
PDF描述 |
|---|---|
| TMS320C6211GNY167 | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMS320C6211GGPA150 | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMS320C6711GGPA120 | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMS320C6211GGPA120 | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMS320C6711GGPA100 | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMS320C6211J100 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMS320C6211J120 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMS320C6211J150 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMS320C6211J167 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMS320C6211JA100 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
發布緊急采購，3分鐘左右您將得到回復。