參數資料
型號: TMS320C6202BGJL167
廠商: Texas Instruments, Inc.
元件分類: 數字信號處理
英文描述: FIXED-POINT DIGITAL SIGNAL PROCESSORS
中文描述: 定點數字信號處理器
文件頁數: 98/123頁
文件大小: 1205K
代理商: TMS320C6202BGJL167
www.ti.com
t
d(IDLEXCOL)
X1/X2
or XCLKIN
XCLKOUT
HALT
HALT
Wake-up Latency
Flushing Pipeline
t
d(WAKEHALT)
(A)
(B)
(C)
(D)
Device
Status
(E)
(G)
(F)
PLL Lock-up Time
Normal
Execution
t
w(WAKE-GPIO)
t
p
GPIOn
Oscillator Start-up Time
TMS320F2808, TMS320F2806
TMS320F2801, UCD9501
Digital Signal Processors
SPRS230F–OCTOBER 2003–REVISED SEPTEMBER 2005
Table 6-18. HALT Mode Timing Requirements
MIN
NOM
MAX
UNIT
cycles
cycles
t
w(WAKE-GPIO)
t
w(WAKE-XRS)
(1)
See
Table 6-11
for an explanation of t
oscst
.
Pulse duration, GPIO wake-up signal
Pulse duration, XRS wakeup signal
t
oscst
+ 2t
c(OSCCLK)(1)
t
oscst
+ 8t
c(OSCCLK)
Table 6-19. HALT Mode Switching Characteristics
PARAMETER
MIN
TYP
MAX
UNIT
cycles
cycles
t
d(IDLE-XCOL)
t
p
Delay time, IDLE instruction executed to XCLKOUT low
PLL lock-up time
Delay time, PLL lock to program execution resume
Wake up from flash
Flash module in sleep state
32t
c(SCO)
45t
c(SCO)
131072t
c(OSCCLK)
1125t
c(SCO)
cycles
t
d(WAKE-HALT)
35t
c(SCO)
cycles
Wake up from SARAM
A.
B.
IDLE instruction is executed to put the device into HALT mode.
The PLL block responds to the HALT signal. SYSCLKOUT is held for approximately 32 cycles before the oscillator is
turned off and the CLKIN to the core is stopped. This 32-cycle delay enables the CPU pipe and any other pending
operations to flush properly.
Clocks to the peripherals are turned off and the PLL is shut down. If a quartz crystal or ceramic resonator is used as
the clock source, the internal oscillator is shut down as well. The device is now in HALT mode and consumes
absolute minimum power.
When the GPIOn pin is driven low, the oscillator is turned on and the oscillator wake-up sequence is initiated. The
GPIO pin should be driven high only after the oscillator has stabilized. This enables the provision of a clean clock
signal during the PLL lock sequence. Since the falling edge of the GPIO pin asynchronously begins the wakeup
procedure, care should be taken to maintain a low noise environment prior to entering and during HALT mode.
When GPIOn is deactivated, it initiates the PLL lock sequence, which takes 131,072 OSCCLK (X1/X2 or X1 or
XCLKIN) cycles.
When CLKIN to the core is enabled, the device will respond to the interrupt (if enabled), after a latency. The HALT
mode is now exited.
Normal operation resumes.
C.
D.
E.
F.
G.
Figure 6-13. HALT Wake Up Using GPIOn
98
Electrical Specifications
相關PDF資料
PDF描述
TMS320M642AGNZ5 1A, 52kHz (250khz Max) Current Mode PWM Control Circuit with 8.4V UVLO Threshold and 96% Max Duty Cycle<sup>3</sup><sup>3</sup><sup>3</sup><sup>3</sup><sup>3</sup><sup>3</sup><sup>3</sup><sup>3</sup><sup>3</sup><sup>3</sup><sup>3</sup> ; Package: 8 LEAD PDIP; No of Pins: 8; Container: Rail; Qty per Container: 50
TMS320DM642GDK500 Adjustable 2.5-36V +/-2.2% Tolerance, 1-100mA Shunt Regulator - PB Free; Package: SOIC-8 Narrow Body; No of Pins: 8; Container: Tape and Reel; Qty per Container: 2500
TMS320DM642GNZ600 Video/Imaging Fixed-Point Digital Signal Processor
TMS320DM642ZDK600 Adjustable 2.5-36V +/-2.2% Tolerance, 1-100mA Shunt Regulator; Package: TO-92 (TO-226) 5.33mm Body Height; No of Pins: 3; Container: Fan-Fold; Qty per Container: 2000
TMS320DM642ZNZ500 Video/Imaging Fixed-Point Digital Signal Processor
相關代理商/技術參數
參數描述
TMS320C6202BGLS100 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR
TMS320C6202BGLS167 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6202BGLW100 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR
TMS320C6202BGLW167 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6202BGLZ167 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS