參數資料
型號： TMP95CW54AF
廠商： Toshiba Corporation
元件分類： 微控制器
英文描述： Quality And Reliability Assurance / Handling Precautions
中文描述： 質量與可靠性保證/操作注意事項
文件頁數： 42/48頁
文件大?。?/td> 390K
代理商： TMP95CW54AF
Quality and Reliability Assurance / Handling Precautions
030901
QUA-42
2002-02-20
(3)
For the minimum clearance specification between
a device and a printed circuit board, refer to the
relevant device’s datasheet or databook. If
necessary, achieve the required clearance by
forming the device’s leads appropriately. Do not
use the spacers which are used to raise devices
above the surface of the printed circuit board during soldering to achieve
clearance. These spacers normally continue to expand due to heat, even
after the solder has begun to solidify; this applies severe stress to the
device.
Observe the following precautions when forming the leads of a device
prior to mounting so as to avoid mechanical stress to the device. Also
avoid ending or stretching device leads repeatedly.
(a)
Use a tool or jig to secure the lead at its base (where the lead meets
the device package) while bending so as to avoid mechanical stress
to the device. Also avoid bending or stretching device leads
repeatedly.
(4)
(b)
Be careful not to damage the lead during lead forming.
(c)
Follow any other precautions described in the individual datasheets
and databooks for each device and package type.
4.5.2 Socket Mounting
(1)
When socket mounting devices on a printed circuit board, use sockets
which match the inserted device’s package.
Use sockets whose contacts have the appropriate contact pressure. If the
contact pressure is insufficient, the socket may not make a perfect contact
when the device is repeatedly inserted and removed; if the pressure is
excessively high, the device leads may be bent or damaged when they are
inserted into or removed from the socket.
When soldering sockets to the printed circuit board, use sockets whose
construction prevents flux from penetrating into the contacts or which
allows flux to be completely cleaned off.
Make sure the coating agent applied to the printed circuit board for
moisture-proofing purposes does not stick to the socket contacts.
If the device leads are severely bent by a socket as it is inserted or
removed and you wish to repair the leads so as to continue using the
device, make sure that this lead correction is only performed once. Do not
use devices whose leads have been corrected more than once.
If the printed circuit board with the devices mounted on it will be
subjected to vibration from external sources, use sockets which have a
strong contact pressure so as to prevent the sockets and devices from
vibrating relative to one another.
(2)
(3)
(4)
(5)
(6)
相關PDF資料
PDF描述
TMP95CW64F Quality And Reliability Assurance / Handling Precautions
TMP95CW65F Quality And Reliability Assurance / Handling Precautions
TMP95PW64F Quality And Reliability Assurance / Handling Precautions
TMP96C041BF Quality And Reliability Assurance / Handling Precautions
TMP95FW54AF Quality And Reliability Assurance / Handling Precautions
相關代理商/技術參數
參數描述
TMP95CW64 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:CMOS 16-Bit Microcontroller
TMP95CW64F 制造商:Toshiba America Electronic Components 功能描述:MCU 16BIT TLCS-900 CISC 128KB ROM 5V 100LQFP - Tape and Reel
TMP95CW65 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:CMOS 16-Bit Microcontroller
TMP95CW65F 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Quality And Reliability Assurance / Handling Precautions
TMP95CW65F(Z) 功能描述:16位微控制器 - MCU TLCS 900/H ROMless w/4K RAM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*