- 您現在的位置：買賣IC網 > PDF目錄365844 > TMP91PW11F (Toshiba Corporation) Quality And Reliability Assurance / Handling Precautions PDF資料下載
參數資料
| 型號： | TMP91PW11F |
| 廠商： | Toshiba Corporation |
| 元件分類： | 微控制器 |
| 英文描述： | Quality And Reliability Assurance / Handling Precautions |
| 中文描述： | 質量與可靠性保證/操作注意事項 |
| 文件頁數： | 44/48頁 |
| 文件大?。?/td> | 390K |
| 代理商： | TMP91PW11F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁
Quality and Reliability Assurance / Handling Precautions
030901
QUA-44
2002-02-20
4.5.4 Flux Cleaning and Ultrasonic Cleaning
(1)
When cleaning circuit boards to remove flux, make sure that no residual
reactive ions such as Na or Cl remain. Note that organic solvents react
with water to generate hydrogen chloride and other corrosive gases which
can degrade device performance.
Washing devices with water will not cause any problems. However, make
sure that no reactive ions such as sodium and chlorine are left as residues.
Also, be sure to dry devices sufficiently after washing.
Do not rub device markings with a brush or with your hand during
cleaning or while the devices are still wet from the cleaning agent. Doing
so can rub off the markings.
The dip cleaning, shower cleaning and steam cleaning processes all
involve the chemical action of a solvent. Use only recommended solvents
for these cleaning methods. When immersing devices in a solvent or
steam bath, make sure that the temperature of the liquid is 50°C or below,
and that the circuit board is removed from the bath within one minute.
Ultrasonic cleaning should not be used with hermetically-sealed ceramic
packages such as a leadless chip carrier (LCC), pin grid array (PGA) or
charge-coupled device (CCD), because the bonding wires can become
disconnected due to resonance during the cleaning process. Even if a
device package allows ultrasonic cleaning, limit the duration of ultrasonic
cleaning to as short a time as possible, since long hours of ultrasonic
cleaning degrade the adhesion between the mold resin and the frame
material. The following ultrasonic cleaning conditions are recommended:
Frequency: 27 kHz to 29 kHz
Ultrasonic output power: 300 W or less (0.25 W/cm
2
or less)
Cleaning time: 30 seconds or less
Suspend the circuit board in the solvent bath during ultrasonic cleaning
in such a way that the ultrasonic vibrator does not come into direct
contact with the circuit board or the device.
(2)
(3)
(4)
(5)
相關PDF資料 |
PDF描述 |
|---|---|
| TMP91PW12F | Quality And Reliability Assurance / Handling Precautions |
| TMP91PW18AF | Quality And Reliability Assurance / Handling Precautions |
| TMP93C071F | Quality And Reliability Assurance / Handling Precautions |
| TMP93CF76F | Quality And Reliability Assurance / Handling Precautions |
| TMP93CF77F | Quality And Reliability Assurance / Handling Precautions |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMP91PW11FG | 功能描述:16位微控制器 - MCU OTP MCU: TLCS-900/L1 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| TMP91PW12F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Quality And Reliability Assurance / Handling Precautions |
| TMP91PW18AF | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Quality And Reliability Assurance / Handling Precautions |
| TMP92C820FG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Original CMOS 16-Bit Microcontroller |
| TMP92CA25FG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Original CMOS 32-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。